|
|
|
Welcome to the Cobra Club Forums forums. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact contact us. |
|
|||||||
| Home | Forums | Blogs | Videos | Cobra Marques | Info | Groups | Classifieds | Gallery | Arcade | Shopping |
| Wiki | Register | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
 |
|
|
LinkBack | Thread Tools | Display Modes |
11-02-07, 10:55 AM
|
|||
|
|||
|
AK Heater
Hi Chaps
Before I start cutting a hole to mount the Polo heater, any advice on measurements from tunnel to bottom of heater. I've read in a previous thread that the heater is very close to the bell housing (Chevy) Any advice welcome Thanks Carl     
|
| Sponsored Links | ||
| ||
|
|
|
11-02-07, 11:09 AM
|
||||
|
||||
|
Carl
A picture speaks a thousand words, this is not my car, but a picture taken at AK's workshop. 
__________________
Mike AK Sportscars 355 Hauser Chevy The old believe everything, the middle-aged suspect everything, the young know everything.
|
|
11-02-07, 11:13 AM
|
|||
|
|||
|
It appears that the heater is mounted very close to the tunnel and across to the drivers side.
Thanks for your help Carl.
|
|
11-02-07, 11:22 AM
|
||||
|
||||
|
Quote:
no mention of this in the manual  however they do advise now not to cut away the sloping front from the heater unit
|
|
11-02-07, 11:31 AM
|
||||
|
||||
|
Quote:
No I didn't ask why, I just did as Ken told me, Its more than likely to get the heater away from the top of the bellhousing. Mine is off centre, but not as much as the one in the photo.
__________________
Mike AK Sportscars 355 Hauser Chevy The old believe everything, the middle-aged suspect everything, the young know everything.
|
|
11-02-07, 11:33 AM
|
||||
|
||||
|
That makes sence
|
| Sponsored Links | ||
| ||
|
|
|
11-02-07, 11:41 AM
|
||||
|
||||
|
Quote:
Just been out to check and there is a plastic bit on the bottom of the heater, if you fitted it central this bit would be very close to the top of the bellhousing, so you will have to fit it offset, but not as much as is shown in the picture.  P.S I see you have fitted yours offset. 
__________________
Mike AK Sportscars 355 Hauser Chevy The old believe everything, the middle-aged suspect everything, the young know everything.
|
|
11-02-07, 12:00 PM
|
||||
|
||||
|
Quote:
There was also a thread a while back on getting it in up-side-down... Carl make sure the outlets are on the RHS looking from the front of the car, into the engine bay 
|
|
11-02-07, 12:03 PM
|
||||
|
||||
|
Quote:
__________________
Mike AK Sportscars 355 Hauser Chevy The old believe everything, the middle-aged suspect everything, the young know everything.
|
|
11-02-07, 12:06 PM
|
||||
|
||||
|
Quote:
 i'll go and take a better one
|
| Sponsored Links | ||
| ||
|
|
|
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Heater | Marc | General Tech Tips & Questions | 20 | 24-08-06 01:06 PM |
| Dax heater | keane | DAX Technical Questions | 19 | 22-01-06 02:10 PM |
| Heater yes or no | ian | General Tech Tips & Questions | 13 | 16-04-04 08:54 PM |
| GD Heater Box. | Trigger | General Tech Tips & Questions | 12 | 21-02-04 04:33 PM |
| heater | Bernie | Pilgrim Sumo Technical Questions | 5 | 20-08-03 09:33 PM |
Linear Mode
