| |
|
Welcome to the Cobra Club Forums forums. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact contact us. |
| |||||||
| Home | Forums | Blogs | Videos Gallery | Cobra Marques | Info | Groups | Classifieds | Gallery | Arcade | Shopping |
| Wiki | Register | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
 |
| | LinkBack | Thread Tools | Display Modes |
13-03-05, 07:11 PM
| |||
| |||
| FRont & rear nudge bar escutcheon plates Anyone know where I can obtain some shiny escutcheon plates to go around the holes where the chrome tubes for the front and rear nudge bars go through the body. I drilled the holes slightly large to allow fitment. I think some little stainless escutcheaon plates would be a great finishing touch and cover the abortion. Ive seen such things fitted on some dax's. Obviously the front ones will have an oval hole as they sit at 45 degrees to the chrome tube Anthony
__________________ ANTHONY Pro cobra builder Current build No. 16      |
| Sponsored Links | ||
| ||
| |
|
13-03-05, 08:45 PM
| ||||
| ||||
| Re: FRont & rear nudge bar escutcheon plates Anthony Have a look here, Gareth is making them. :thumb: :thumb: LS1/SBC oil filters... anyone need any?
__________________ AK 427 FOR SALE PistonHeads AK for sale Mike AK Sportscars 355 Hauser Chevy The old believe everything, the middle-aged suspect everything, the young know everything. |
|
14-03-05, 06:14 PM
| |||
| |||
| Re: FRont & rear nudge bar escutcheon plates I remember this thread funny enough I posted it. I think its a little on the expensive side for a few glorified washers though. Anywhere cheaper Anthony
__________________ ANTHONY Pro cobra builder Current build No. 16 |
|
14-03-05, 07:01 PM
| ||||
| ||||
| Re: FRont & rear nudge bar escutcheon plates Dax sell them  I cheated on the rears and polished up some 15mm stainless washers (pennies)
__________________ Chris AK 427 351C T5wc |
|
14-03-05, 07:43 PM
| |||
| |||
| Re: FRont & rear nudge bar escutcheon plates THanks chriss will give dax a call tomorrow before I dart off to sunny Las Vegas. Where did you get the 15mm washers from, I can only find them in a repair type washer upto 13mm Anthony
__________________ ANTHONY Pro cobra builder Current build No. 16 |
|
14-03-05, 07:54 PM
| ||||
| ||||
| Re: FRont & rear nudge bar escutcheon plates Just found 4 spares in the garage PM your address and I'll post them :thumb:
__________________ Chris AK 427 351C T5wc |
| Sponsored Links | ||
| ||
| |
|
14-03-05, 08:07 PM
| |||
| |||
| Re: FRont & rear nudge bar escutcheon plates Thaks chriss have sent address via PM Anthony
__________________ ANTHONY Pro cobra builder Current build No. 16 |
|
16-03-05, 12:23 PM
| |||
| |||
| Re: FRont & rear nudge bar escutcheon plates Anthony Keep us posted as to how you get on.I am interested in the same. Thx Phil |
| Sponsored Links | ||
| ||
| |
|
| Thread Tools | |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Escutcheon plates supplier | bitsilly | General Cobra Discussion | 8 | 28-09-07 04:31 PM |
| Nudge Bar Escutcheon Plates | Almac | General Cobra Discussion | 4 | 10-01-06 11:17 PM |
| Exhaust Escutcheon Plates | Almac | General Tech Tips & Questions | 13 | 23-11-05 10:28 PM |
| Grommets for rear nudge bar and front overriders | JP | AK Technical Questions | 9 | 11-08-04 07:56 AM |
| Front & Rear Nudge Bar Fitment & oil temp sender | kdavies3 | General Tech Tips & Questions | 8 | 14-06-02 12:16 PM |
Linear Mode
