Search:

Type: Posts; User: jon1d; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Heavy Clutch

    by jon1d
    Replies
    35
    Views
    3,520

    Measure your idle vacuum which should be around...

    Measure your idle vacuum which should be around 12-15 ins/hg and you will be fine in traffic. Some high lift cams only give you about 5 ins/hg which is where you will have issues.
  2. Replies
    2
    Views
    159

    https://youtu.be/UMZ8_pqJgek

    https://youtu.be/UMZ8_pqJgek
  3. Thread: Tyres

    by jon1d
    Replies
    5
    Views
    307

    I was surprised with the wall difference of the...

    I was surprised with the wall difference of the Galaxy to my old GF Goodrich tyres . The Galaxy wall was a lot straighter and I could of easily gone up a size or two. Galaxy to my old hard GF was...
  4. Thread: Tyres

    by jon1d
    Replies
    5
    Views
    307

    Have you gone off the Galaxy's? I have seen Avon...

    Have you gone off the Galaxy's? I have seen Avon 225/65R15 on the front of a few cars. Avons have a straighter wall. Your 235 Galaxy section widths are 9.15 and the Avons are 9.1.

    It also depends...
  5. Replies
    7
    Views
    304

    You need the cap as you say for filling and...

    You need the cap as you say for filling and venting as it will be the highest point . Mount the expansion tank as close to the engine as.possible will give you more headroom between the filler cap...
  6. Replies
    7
    Views
    304

    Your expansion tank is far to low. The pipe needs...

    Your expansion tank is far to low. The pipe needs to be flat going into the tank and the top of expansion tank height above the thermostat housing. Raising the tank will elevate the air pocket issue....
  7. Replies
    3
    Views
    289

    I would peel back the film where you pop rivet or...

    I would peel back the film where you pop rivet or any fixings but leave the rest in place to protect it as much as possible and remove it when you have fitted everything in place.
    Bending, shaping...
  8. Thread: Which oil

    by jon1d
    Replies
    7
    Views
    430

    This might work with your dry sump. It does not...

    This might work with your dry sump. It does not cost a lot. I think its work using for all engines to reduce cold start up.

    https://www.youtube.com/watch?v=pFoHZ-kAcQY
  9. Replies
    4
    Views
    228

    Thanks Phil , I am sure someone will post...

    Thanks Phil ,
    I am sure someone will post recommendations. I only know about Jaguar set up .
  10. Replies
    4
    Views
    228

    What vehicle and running gear xj6/12 early or...

    What vehicle and running gear xj6/12 early or xj40?
  11. Replies
    9
    Views
    427

    Just before the weekend storm.

    Just before the weekend storm.
  12. Some interesting facts they dont want to...

    Some interesting facts they dont want to publicise. The amount of co2 generated from volcanic eruptions around the world makes made co2 a fraction. On average 200 volcanic eruptions are occurring. ...
  13. Thread: Clutch Pipe

    by jon1d
    Replies
    6
    Views
    372

    Flexible will be a lot easier to fit. Ridged will...

    Flexible will be a lot easier to fit. Ridged will allowing for less movement.
  14. Replies
    9
    Views
    458

    Yes a build thread is ideal .Also it's a good...

    Yes a build thread is ideal .Also it's a good record of your progress.
  15. Replies
    25
    Views
    971

    Yes I believe you can apply for new historical...

    Yes I believe you can apply for new historical status on the 40 birthday shown on your V5C "date of first registration" in section 4B . I sent mine off a few weeks early. Once it is on the V5c you...
  16. So could we see a petrol engine just for show and...

    So could we see a petrol engine just for show and for the noise with electric motor drive train.
    Fast forward 2035. Electric motors will be half the size for twice the power. Batteries will be...
  17. Replies
    9
    Views
    458

    Hi Glen, Nice to see some photos on your...

    Hi Glen,
    Nice to see some photos on your progress and the chassis design. I am sure you will get lots of encouragement from the forum and post any question as someone has probably had the same...
  18. Replies
    25
    Views
    971

    Date on the V5C for the 40 years rollover. I took...

    Date on the V5C for the 40 years rollover. I took my V5c and it disappeared in the postal DVLA system. So it ended up costing me £25 for a new V5c. Send it registered post.
    My car was correctly...
  19. Replies
    22
    Views
    1,200

    You paid extra for the rusty bolts. I have...

    You paid extra for the rusty bolts. I have started to look at using allen socket bolts as they come in 12.9 grade high tensile strength imperial UNF also less chance of rounding plus easier access. I...
  20. Replies
    22
    Views
    1,200

    After your findings I am inspecting every nut and...

    After your findings I am inspecting every nut and bolt for markings when I dismantle any part. A major are stamped . How do you know what you have with no stamp. It seems they are neglecting the...
  21. Replies
    9
    Views
    427

    Just cover the cock pit area .Ideal if you have a...

    Just cover the cock pit area .Ideal if you have a tarpaulin cover. Tape down front edges and bungie cord under the car and over top.
  22. Thread: Ground Clearance

    by jon1d
    Replies
    8
    Views
    431

    Speed bump clearance height is required with a...

    Speed bump clearance height is required with a sump guard fitted. The minimum height should be 100 mm. The sump or gearbox housing is usually the lowest point.
    ...
  23. Thread: Brake Issue

    by jon1d
    Replies
    18
    Views
    1,403

    Are they leaking from the bridge link pipe and...

    Are they leaking from the bridge link pipe and did they supply them?
  24. Replies
    17
    Views
    1,360

    Make sure you give it a good wipe...

    Make sure you give it a good wipe down.Interesting if it matches up to good old British workmanship.
  25. Replies
    8
    Views
    427

    Pete, If you have the measurements of the...

    Pete,

    If you have the measurements of the lower shock mount bush. You might find it in the universal sizes. I think the older bushes creaked and looking at the latest ones they are better fitting...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4