Search:

Type: Posts; User: RichP; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: corsa b repair

    by RichP
    Replies
    2
    Views
    262

    Thank you Aaron, just what hat I needed to...

    Thank you Aaron,

    just what hat I needed to know, sounds like a straight forward job.

    Regards

    Rich
  2. Thread: corsa b repair

    by RichP
    Replies
    2
    Views
    262

    corsa b repair

    Hi Guy’s, replacing the Corsa B top column bearing

    i have read the the threads regarding finding the bearing etc. I now have this bearing and from the limited information that I can find it...
  3. Replies
    8
    Views
    822

    I think the Sump is a Champ Pan after looking...

    I think the Sump is a Champ Pan after looking them up, it is a 7 quart CP57Ltr 7 inch Oil Pan.

    Have a good rest of the week.

    Regards

    Rich
  4. Replies
    1
    Views
    335

    Hi BW, I can measure mine tonight and include...

    Hi BW,

    I can measure mine tonight and include a photo on an email if that would be assistance, if it would help please forward an email address and I will get it measured.


    Regards

    Rich
  5. Replies
    8
    Views
    822

    Hi Guy's thank you for all of your valuable...

    Hi Guy's thank you for all of your valuable feedback !!

    If I get some photo's of the Sump on the Cobra will that enable us to be able to confirm if is one of these Champ Pans ? I know that it has...
  6. Replies
    8
    Views
    822

    Hi All, Thank you for all of your reply’s. ...

    Hi All,

    Thank you for all of your reply’s.

    The issue that I have is that a new Dip Stick came with the new sump and was not marked with high or low fill marks.
    i fitted the Sump and Dip...
  7. Replies
    8
    Views
    822

    Mike Hubbard Sump

    Hi Guy’s

    just in case anyone may know, about 3 years ago I fitted a Mike Hubbard Winged Sump to the V8 Chevy because the existing one was too tall giving limited ground clearance. I am now...
  8. Replies
    8
    Views
    662

    Hi James, What a kind offer !! Yes for sure...

    Hi James,

    What a kind offer !!

    Yes for sure if that will be okay with you, will of course look after your equipment etc.

    Can you confirm a mobile number please so that I can contact you.
    ...
  9. Replies
    8
    Views
    662

    Hi James, Thank you for your feedback, very...

    Hi James,

    Thank you for your feedback, very useful !!

    I will be hiring an engine crane, can you remember the complete length of the arm including your 6" extension please so that I can try and...
  10. Replies
    8
    Views
    662

    Hi David, Thank you for your very helpful...

    Hi David,

    Thank you for your very helpful reply, it sounds as straight forward as it looks, I have had the Cobra now for about 6 years, it was built in 2002 to a good standard but with the engine...
  11. Replies
    8
    Views
    662

    Removing Chevy V8 Out Of Dax Cobra

    Hi Guy’s,

    i want to to remove the engine to make good the engine bay and spruce up the engine etc. Is is best to support the Bell Housing and remove the engine or is it better to remove the...
  12. Replies
    11
    Views
    1,423

    Hi Sean, thanks for digging that out, I will...

    Hi Sean,

    thanks for digging that out, I will compare and see what it is, I had forgot that I had posted the earlier questions, the aim was to achieve assistance with more feel

    Regards

    Rich
  13. Replies
    11
    Views
    1,423

    Hi All, To check the Steering Column type, if...

    Hi All,

    To check the Steering Column type, if I take some photo's tonight, is there anyone that I can send the photos' to t confirm Ford or Vauxhall

    Best Regards

    Rich
  14. Replies
    11
    Views
    1,423

    Hi 1dayiwill, Thank you for your feedback,...

    Hi 1dayiwill,

    Thank you for your feedback, this looks a good solution for the Bulkhead, but I am actually talking about the bearing at the op of the column just behind the steering wheel. Have you...
  15. Replies
    11
    Views
    1,423

    Hi Gumball, Thank you or your prompt feedback,...

    Hi Gumball,

    Thank you or your prompt feedback,

    My Column looks to be the older Ford ? with the Hazard Light Switch in the centre of the top black plastic cover behind the wheel, the Cobra was...
  16. Replies
    11
    Views
    1,423

    Steering Column Bush Play

    Hi Guy's

    Over the time that I have had the Cobra I have refined and improved it it runs and drives very well the only little thing left as I am splitting the atom is my wish to remove the slight...
  17. Replies
    13
    Views
    1,921

    Hi Guy’s, Just wanted to confirm what I...

    Hi Guy’s,

    Just wanted to confirm what I found was the issue.

    it was the bolt bottoming out before clamping to the required level. all recommendations carried out and all is now sorted
    ...
  18. Replies
    13
    Views
    1,921

    Good Feedback Thanks Steve, will do. Rich

    Good Feedback

    Thanks Steve, will do.

    Rich
  19. Replies
    7
    Views
    2,073

    Hi Guy’s Just a short note to ask if any of...

    Hi Guy’s

    Just a short note to ask if any of you were at the Pangbourne Classic car day yesterday, there were 4 Cobra’s there. It was a very good relaxed event with 200 very different...
  20. Replies
    13
    Views
    1,921

    Hi Andy, will check, I thought I had it with the...

    Hi Andy, will check, I thought I had it with the grippy bit facing down but will also look this

    Thanks

    Rich
  21. Replies
    13
    Views
    1,921

    Hi Conrod, i will also check if the bolt is...

    Hi Conrod,

    i will also check if the bolt is bottoming, hadn’t thought of that, as the bolt should be tight enough to clamp the Dizzy, I will quickly put a thicker washer under the bot head and...
  22. Replies
    13
    Views
    1,921

    Thank you you all for your great feedback, I will...

    Thank you you all for your great feedback, I will now put the black plastic shim back and call Real Steel Monday morning.

    Have a good rest of the weekend

    Regards

    Rich
  23. Replies
    13
    Views
    1,921

    Chevy V8, Distributor

    Hi Guy’s,

    i have always had had the issue of the Distibutor coming loose and rotating advancing the timing etc. Just now replaced the Inlet Manifold Gaskets due to water leak. The Gasket set...
  24. Replies
    12
    Views
    1,954

    Forgot to mention that I found the reason for the...

    Forgot to mention that I found the reason for the cooling fan not cutting in at the required temperature, the sensor had been tie rapped to the outside of the top hose/aluminium tube. When putting...
  25. Replies
    12
    Views
    1,954

    Just as an update, I now have the inlet manifold...

    Just as an update, I now have the inlet manifold off, all went well starting with draining the water, the most difficult part being removing the manifold that was well stuck to the block and heads....
Results 1 to 25 of 213
Page 1 of 9 1 2 3 4