Search:

I only have Oil Pressue (no temperature) in a standard 6 gauge setup - speedo, tach, oil pressure, water temp, fuel, volts

My oil pressure sender (ETB instruments standard sender from circa 2000) is a combined sensor and switch – i.e. it drives both the gauge and the warning light via two separate outputs. Hence only...

Good morning all.

Just a quick reminder and update on registration for the Cranleigh show. The registration deadline has been extended to 8th July (next Sunday). Details on how to register and...

Sean & Tony - cool, see you both there...

Good morning all.

Just a quick reminder and update on registration for the Cranleigh show. The registration deadline has been extended to 8th July (next Sunday). Details on how to register and...

Good morning all.

Just a quick reminder and update on registration for the Cranleigh show. The registration deadline has been extended to 8th July (next Sunday). Details on how to register and...

Good morning all.

Just a quick reminder and update on registration for the Cranleigh show. The registration deadline has been extended to 8th July (next Sunday). Details on how to register and...

Good morning all.

Just a quick reminder and update on registration for the Cranleigh show. The registration deadline has been extended to 8th July (next Sunday). Details on how to register and...

I didn't.
What are you having a problem with - I'll help if I can.

Re-posted here in case you miss it in the Events section - hope that's ok.

Cranleigh Classic Car Show and Autojumble Sunday 12 August 2018

I’ve not seen anything about arrangements for this,...

Re-posted here in case you miss it in the Events section - hope that's ok.

Cranleigh Classic Car Show and Autojumble Sunday 12 August 2018

I’ve not seen anything about arrangements for this,...

Re-posted here in case you miss it in the Events section - hope that's ok.

Cranleigh Classic Car Show and Autojumble Sunday 12 August 2018

I’ve not seen anything about arrangements for this,...

Re-posted here in case you miss it in the Events section - hope that's ok.

Cranleigh Classic Car Show and Autojumble Sunday 12 August 2018

I’ve not seen anything about arrangements for this,...

Cranleigh Classic Car Show and Autojumble Sunday 12 August 2018

I’ve not seen anything about arrangements for this, so I’ve gone ahead and registered the Cobra Club so that everyone attending...

Interesting... My sump is fractionally lower than the bellhousing (and I think i'd rather it was).

Does anyone know if anything has been arranged for the Cranleigh show this year? I see club registration closes on July 1st, but I’ve not seen anything on here about it?
I'd check on the Official...

Just wondering how much ground clearance you folks are running. I took the cobra out for a run last weekend and managed to drop the nearside wheels into a bit of subsidence at the side of the road...

Test fit the rubber bits, trim to suit and use sealant especially at the ends. I had to trim the triangles that fill the head-to-block chamfer at the ends of mine as it was clear they weren't going...

Markus,
When I did a forum and internet search, what I found suggested that 5 to 6 degrees was about right. When I adjusted mine, I aimed for 6. I've not really driven it since the adjustments to...

Markus,
I changed mushrooms from shorter to taller at the same time (because I'm running Sierra, 4-stud, uprights).
When my car was built, we didn't set the caster at all, but just bolted it all up...

Markus,
I recently made the same exchange (new wishbones) as you, and at the time took a few measurements. It's not an exact measurement of the displacement towards the read that the new style...

Having spent a while working out what I needed, I can see that fitting them to the controller isn't practical. They have to be matched to the load, both in terms of current draw and resistance, with...

Some of you may know of Spiyda - makers of interesting and useful electronic automotive gadgets. I bought a dual fan controller a couple of years ago to regain proper contol of my radiator fans....

Also, a few videos on YouTube explaining setup...
https://www.youtube.com/watch?v=eikgtwSIMXo
https://www.youtube.com/watch?v=oepa7TrT6Cc

Can anyone recommend a decent trimmer in West Sussex for a simple tonneau modification? I need someone to cut two new roll-bar holes, trim the edges and fit a Velcro closure to an existing tonneau. I...