Search:

Type: Posts; User: sunday; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    223

    PM send. Stéphane.

    PM send.

    Stéphane.
  2. Replies
    5
    Views
    223

    I will have a look this evening when back to home.

    I will have a look this evening when back to home.
  3. Replies
    5
    Views
    223

    Hi, if necessary I have a late version which...

    Hi, if necessary I have a late version which covers mkiv chassis.

    Stéphane.
  4. Replies
    31
    Views
    5,091

    I've done a diagram from the one's i've machined...

    I've done a diagram from the one's i've machined :

    http://www.cobraclub.com/forum/attachment.php?attachmentid=39841&stc=1

    All dimensions are in mm.
    The right side must retain your attention as...
  5. Replies
    31
    Views
    5,091

    Happy you appreciate. For managing end float i...

    Happy you appreciate. For managing end float i made custom washer adjusted with magnetic grinding machine to obtain a near 0 end float. I do that as i cant buy din988 washers in small qty in France.
  6. Replies
    17
    Views
    1,816

    I've done some "homework" and plan to rebuild dif...

    I've done some "homework" and plan to rebuild dif this winter to 3.07 ratio and with derating of clutch plates.
    I've ordered a Motive gear dana44 3.07 ratio crown+pinion which need some...
  7. Replies
    31
    Views
    5,091

    Some news : i've ordered early stub axle, new...

    Some news : i've ordered early stub axle, new timken bearings and made a custom reinforcing kit as illustrated in attached picture. Hope it will be a good and robust config.
    39822
  8. Replies
    26
    Views
    3,640

    I plan to bolt body to chassis with top aluminium...

    I plan to bolt body to chassis with top aluminium ribbon plates to have more uniform efforts. I think to put also rubber ribon under body to avoid squeak noise. My goal is to keep possibility to...
  9. Replies
    26
    Views
    3,640

    Chassis has been paint with polyurethane paint,...

    Chassis has been paint with polyurethane paint, old trans tunnel removed and then make a try to mary them together ... measures and cad modeling seem to be correct, perfect fit !
    39777
  10. Replies
    17
    Views
    1,816

    Thanks for this info. I've tested with...

    Thanks for this info. I've tested with dynamometer and mine is locked at least until 100lbs so for sure not derated (this can explain "strange" behaviour on corners at low speed of the car before i...
  11. Replies
    17
    Views
    1,816

    I am very interessed to know how derate the dif...

    I am very interessed to know how derate the dif to lower friction, have you put new parts, suppress some plates or ???
    Also what range of derated locking torque will be fine on our light cars ?
  12. Replies
    17
    Views
    1,816

    No sign of wear of what i can see without...

    No sign of wear of what i can see without dissassembly and oil was quite clean with no strange "things" in it.
    I will try with a bar to see if plates are really locked.
    I am searching infos of...
  13. Replies
    17
    Views
    1,816

    Strange for me but after additionnal searches it...

    Strange for me but after additionnal searches it seems to be a type E diff unit. I've found a thread (https://relicrecyclery.com/Jaguar/page30/63XKE_30.htm) and i think i have the same unit. If...
  14. Replies
    26
    Views
    3,640

    This forum is really helpfull and i like the...

    This forum is really helpfull and i like the positive state of mind of the members, no problem to share or help (via mp) when a member will go to that route.
    39688
  15. Replies
    26
    Views
    3,640

    I've retreive cad datas : dax back bone give +30%...

    I've retreive cad datas : dax back bone give +30% in torsionnal rigidity :
    39687
  16. Replies
    26
    Views
    3,640

    I've done cad simulations with dax back bone, i...

    I've done cad simulations with dax back bone, i will try this evening to find model and give numbers for comparison if some interrest.
    I've done tests with my seats and it's fine but effectivly need...
  17. Replies
    26
    Views
    3,640

    Some rigidity numbers : early irs chassis...

    Some rigidity numbers :
    early irs chassis without backbone brace : 10900 N.m/deg
    early irs with this backbone design : 18600 N.m/deg
    These are cad modeled numbers which indicates improvement...
  18. Replies
    26
    Views
    3,640

    Safety first as propshaft can be very dangerous....

    Safety first as propshaft can be very dangerous.
    For rigidity, multiple cad designs and choice to the one who give the maximum torsionnal rigidity with minimal weight : this extra weight (<20kg) is...
  19. Replies
    17
    Views
    1,816

    Dif rebuild questions

    Hi, hereafter a pic of my dif :
    39681

    Can someone confirm that it's a XJ6 S1 60-63 dif ? (I have the stub axle big nut outside) : is-it a ball-bearing or a tapered bearing stub axle type ?
    I've...
  20. Replies
    26
    Views
    3,640

    Some news, chassis has been "cold" zinc plated...

    Some news, chassis has been "cold" zinc plated with zinc gun so now go to paint shop for a polyurethane spray !
    39680
  21. Replies
    9
    Views
    1,115

    Nice ! Is this custom made hat ?

    Nice ! Is this custom made hat ?
  22. Replies
    9
    Views
    1,115

    Some news : front hat have been CAD designed with...

    Some news : front hat have been CAD designed with these pcd numbers. Before 7075 machining, i've 3d print an abs part to verify all my clearance measures to the wheel and confirm caliper mounting...
  23. Replies
    9
    Views
    1,115

    Thanks you give right info as measures from...

    Thanks you give right info as measures from number 1 to 2 or 1 to 3 bolts confirm your numbers. I assume pcd is on a 4.375" pattern.

    For the rear i ve done search on spicer parts but for now not...
  24. Replies
    9
    Views
    1,115

    Thanks for the fast response. I think this pcd is...

    Thanks for the fast response. I think this pcd is the one of the wheel studs. What i am looking for is the pcd of the disc fixations on the axle (5 bolts fronts, 4 on the rear on the IRS side that...
  25. Replies
    9
    Views
    1,115

    XJ6 front & rear disc bolt pattern

    Hi everyone, i'am searching with no success the front and rear bolt pattern of xj6 discs to do my homework and machine my 7075 HAT, if someone has this info it will be very helpfull :D
Results 1 to 25 of 72
Page 1 of 3 1 2 3