Search:

Type: Posts; User: Julesdm; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    294

    Looks good Mark....not long now......just got to...

    Looks good Mark....not long now......just got to take all those sharp bits off now!!!!

    Jules
  2. Replies
    23
    Views
    618

    Dude you have a car to build......decorating will...

    Dude you have a car to build......decorating will have to wait!!
  3. Replies
    23
    Views
    618

    Brian from Roadcraft again emailed me last night...

    Brian from Roadcraft again emailed me last night and we have concurred that the bellhousing must be at fault. So i have to wait for first week in December to take it down to him for checking. It...
  4. Replies
    23
    Views
    618

    dowels are 0.622" in diameter and 1.2" long Aaron

    dowels are 0.622" in diameter and 1.2" long Aaron
  5. Replies
    23
    Views
    618

    We did and it was true......i will double double...

    We did and it was true......i will double double check again later today.
  6. Replies
    23
    Views
    618

    The short measurement is at 22.30. I did google...

    The short measurement is at 22.30. I did google line boring and it does mention this would move a crank towards the cam shafts, but, yes i do agree....not by 2mm........
  7. Replies
    23
    Views
    618

    1. we checked the flywheel ran true and flat to...

    1. we checked the flywheel ran true and flat to the block.
    2. we checked the face of the bellhousing was parallel to the flywheel. It wasnt and so we shimmed and got the face parallel.
    3. We...
  8. Replies
    23
    Views
    618

    I dont, it was a custom build engine from USA...

    I dont, it was a custom build engine from USA (excluding bellhousing)and i have purchased the bellhousing and Tremec in the UK. Next engine i buy, i will get the builder to mount the flywheel and...
  9. Replies
    23
    Views
    618

    Brian from Roadcraft has emailed me as he is on...

    Brian from Roadcraft has emailed me as he is on holiday and reckons it could be the Line Boring of the block has caused the crank to move. He is willing to check the bellhousing but is sure his CNC...
  10. Replies
    23
    Views
    618

    Confusingly, whenbwe did the run out before...

    Confusingly, whenbwe did the run out before parallel, at the weekend. The runout was 2.1mm.....so pretty much the same.....
  11. Replies
    23
    Views
    618

    it is a brand new Roadcraft cnc aluminium...

    it is a brand new Roadcraft cnc aluminium bellhousing.
  12. Replies
    23
    Views
    618

    Dial in Bellhousing HELP!

    Evening.

    Right, i have now after much effort and frustration and heated discussion with my dad (assistant) shimmed the bellhousing to parallel. 0.032 and 0.006 at opposite bottom corners pushed...
  13. Replies
    2
    Views
    231

    Parallel Bellhousing

    Just a quick one. I am mounting my bellhousing onto my 1973 machined cbs 350 block.

    I am obviously checking parallel before run out.

    My bellhousing is off by 2mm at 6o'clock. It needs kicking...
  14. Thread: Heat 3

    by Julesdm
    Replies
    3
    Views
    639

    Nigel I have to be honest......i copied your...

    Nigel

    I have to be honest......i copied your design! Aluminium sheet 1mm etc etc..... 150mm M8 bolts through to secure and riv nuts to the bulk head......but it would appear from lack of response...
  15. Thread: Heat 3

    by Julesdm
    Replies
    3
    Views
    639

    Heat 3

    just installing the heat 3 unit. I have built an aluminium box to house the unit with 50mm inlet holes on the left and right vertical sides.

    Before I drill 50mm holes in the stainless foot wells....
  16. Replies
    9
    Views
    664

    Mark saw your car at the weekend......nice paint...

    Mark saw your car at the weekend......nice paint job, looked good.
  17. Replies
    9
    Views
    664

    Engine certification

    Can someone point me in the direction of a thread on here recently that identified all the firms that will certify the engine age. I know Knight Racing will do it.......but there were others and some...
  18. Replies
    6
    Views
    445

    FYI turned out to be M12 male unions.

    FYI turned out to be M12 male unions.
  19. Replies
    4
    Views
    385

    Earth Petrol Filler Cap

    I have read a lot about people running an earth from the aston filler cap.

    As i am planning on bonding the base down i will not have any fixings.

    Is this earth an IVA necessity? I dont think i...
  20. Thread: 427 top oiler

    by Julesdm
    Replies
    5
    Views
    399

    http://www.realsteel.co.uk/# should help you

    http://www.realsteel.co.uk/# should help you
  21. Replies
    7
    Views
    415

    Nice lights.....However, love the mid rise...

    Nice lights.....However, love the mid rise lift....which i am shortly in the market for......which one did you go for?

    Regards

    Jules
  22. Replies
    6
    Views
    445

    No tried that too small

    No tried that too small
  23. Replies
    6
    Views
    445

    Rover 25 male brake union size

    Quick one.....when refurbing my master cylinder and servo, I threw away the old male unions and pipe they cut when extracting from the doner car.
    Went to install a 7/16...too small...tried a...
  24. Replies
    5
    Views
    396

    Rolling chassis done, engine delay from...

    Rolling chassis done, engine delay from USA.....should be here in3 weeks. Have all parts to complete build, just need body on chassis. Fitted usual bits on body that can be done before mounting. Just...
  25. Thread: What tyres????

    by Julesdm
    Replies
    15
    Views
    949

    Nice, i will do exactly that.

    Nice, i will do exactly that.
Results 1 to 25 of 49
Page 1 of 2 1 2