Search:

Type: Posts; User: James Fishwick; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Hi Ian, I have emailed you as it was easier. ...

    Hi Ian,

    I have emailed you as it was easier.

    best regards
    James
  2. thank you all, I really appreciate your comments....

    thank you all, I really appreciate your comments. I was surprised when it was suggested I add the bracket as I had understood it wasn't necessary.
  3. chassis attachment for seat belt anchors glassed into the body

    Hi All,

    I have heard this discussed previously but can't find any pics of what others have done. I am not sure if it is necessary but I have been recommended to attach the seat belt anchor metal...
  4. Thank you all for advice. Anthony it would be...

    Thank you all for advice. Anthony it would be great to discuss options and costs with you. I will try and give you a call tomorrow or early next week.
  5. Paint and body prep in the south west

    Hi all,

    I am getting closer to needing to sort out where I will get my car prepared and sprayed. I am in Plymouth and hoping for some recommendations as to who others have used and could...
  6. Replies
    14
    Views
    1,441

    I ordered mine yesterday and decided to go with...

    I ordered mine yesterday and decided to go with the anodized, from the comments above this sounds like the right decision.

    I now have 10 weeks to decide what tyres to put on them!!! I went with...
  7. Replies
    14
    Views
    1,441

    Thank you for your feedback. I have had a chat...

    Thank you for your feedback.

    I have had a chat with Image Wheels again today and they have been very helpful. They are going to send me a picture of a polished wheel and an anodized wheel side by...
  8. Replies
    14
    Views
    1,441

    Image Wheels

    It is that time in the build process when the wheels need to be ordered. I realise that wheels are a very personal choice and I have decided to go with the Image wheels GTD5's in 17 inch. I...
  9. Replies
    13
    Views
    3,293

    Yes perhaps a bit optimistic but I was very...

    Yes perhaps a bit optimistic but I was very reluctant to spray my powder extinguisher over my engine.

    Interestingly it did only burn momentarily and then just steamed a lot.

    As the exhaust wrap...
  10. Replies
    13
    Views
    3,293

    I can certainly vouch for coolant being...

    I can certainly vouch for coolant being flammable. Watch below from about 2:50. My fault I didn't have the cap on properly.

    https://www.youtube.com/watch?v=ayFlhtrDi10
  11. Replies
    13
    Views
    3,293

    exhaust wrap coating

    All those that use exhaust wrap on their headers has anyone sprayed the wrap with Themo-Tec exhaust wrap coating, for example?
    ...
  12. Replies
    22
    Views
    6,873

    Good to hear it is all running. I am far from an...

    Good to hear it is all running. I am far from an expert but I was advised regarding timing from some very knowledgeable guys on this forum.

    http://www.cobraclub.com/forum/showthread.php?t=57677
    ...
  13. Replies
    22
    Views
    6,873

    I was advised to set my timing to 12-14 advanced...

    I was advised to set my timing to 12-14 advanced at tick over. That is all in mech and vac.
  14. Replies
    22
    Views
    6,873

    I am starting to get my head around setting up...

    I am starting to get my head around setting up the carb and would be interested to know what you did. Also your engine size? Thank you.
  15. Replies
    22
    Views
    6,873

    You can still use the manual choke with no cable...

    You can still use the manual choke with no cable but it will cancel if you use the throttle. I have a 3.5 with Edlebrock 500 (which is factory settings) and use my choke for tick over when...
  16. Replies
    3
    Views
    925

    Wiper motor

    I am looking to purchase a suitable wiper motor kit for my Pilgrim Sumo mk3 build. I have seen a kit in car builder solutions that looks ideal but I am unsure of which sweep angle to choose. I am...
  17. Replies
    2
    Views
    1,034

    Hi David, Jim at JRV8 might be able to help...

    Hi David,

    Jim at JRV8 might be able to help you out. Failing that search for a seller called room05 on ebay as he has helped me with a lot of parts before. If he doesn't have what you need on...
  18. Replies
    9
    Views
    2,858

    Thank you for all the feed back. I think for the...

    Thank you for all the feed back. I think for the sake of my neighbor's I will fit the choke.
  19. Replies
    9
    Views
    2,858

    RV8 Choke

    I have read in several places that people don't tend to fit the choke to a RV8 engine. I have a 3.5L RV8 with Edlebrock 1404 carb. If I start it using the choke on full and gradually let it off in...
  20. Replies
    26
    Views
    6,984

    Yes very relieved it was the gasket. I...

    Yes very relieved it was the gasket. I completely rebuilt the engine myself having never done anything like it before. I think it will be a while before I can relax when it is running, I keep...
  21. Replies
    26
    Views
    6,984

    Now that makes more sense, thank you.

    Now that makes more sense, thank you.
  22. Replies
    26
    Views
    6,984

    On my ETB gauges the oil pressure gauge has LB/O"...

    On my ETB gauges the oil pressure gauge has LB/O" as a unit. What is this and how does it compare to psi? thank you.
  23. Replies
    26
    Views
    6,984

    New gaskets arrived today and now all fitted and...

    New gaskets arrived today and now all fitted and torqued up. Engine sounding much better and no noises from around the manifolds.

    Whilst I have the Pilgrim manifolds my side pipes are custom...
  24. Replies
    26
    Views
    6,984

    I was just looking at my exhaust manifold, which...

    I was just looking at my exhaust manifold, which is a plate that spans all 4 chambers with tubes welded to it. If I place it face down on a flat surface (I used my spirit level) it curls up about...
  25. Replies
    26
    Views
    6,984

    Absolutely it was somewhat of a relief to see.

    Absolutely it was somewhat of a relief to see.
Results 1 to 25 of 165
Page 1 of 7 1 2 3 4