Search:

Type: Posts; User: dave; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.15 seconds.

  1. Replies
    22
    Views
    1,043

    M10 x 25mm stainless dome head screw. Drilled...

    M10 x 25mm stainless dome head screw.
    Drilled 5mm and tapped M6 down the middle.
    The head is then machined to a flat disc. ;-)
  2. Replies
    9
    Views
    1,306

    How many of the 3 terminals are you using, and...

    How many of the 3 terminals are you using, and what for?
  3. Replies
    9
    Views
    1,306

    Not sure if I have skipped past the answer to...

    Not sure if I have skipped past the answer to this. But... What gauges do you have? As that will be the right place to get the switch from. ;-)
  4. Thread: Bristol Iva

    by dave
    Replies
    9
    Views
    1,921

    What Anthony says. There is no "On the fence"...

    What Anthony says.
    There is no "On the fence" when it's stated in the manual.
  5. Replies
    16
    Views
    3,764

    What thread are your knock on hubs? I might have...

    What thread are your knock on hubs?
    I might have some hex nuts you can borrow ;-)
  6. Replies
    62
    Views
    7,356

    Good find Drammyboy. There is usually more to a...

    Good find Drammyboy.
    There is usually more to a story than the attention grabbing headline.

    There was once a Texan guy who tried to stop Factory 5 from making Cobra replicas. He lost, but F5 (and...
  7. Thread: Chassis Talk

    by dave
    Replies
    32
    Views
    4,251

    Possible. But I'm booked up until December 2023....

    Possible.
    But I'm booked up until December 2023. ;-)
  8. Thread: Chassis Talk

    by dave
    Replies
    32
    Views
    4,251

    If only it had stopped at £4000 ;-) It's 7...

    If only it had stopped at £4000 ;-)

    It's 7 years now since the first body arrived. The chassis is at least another year or so older. :-O
  9. Replies
    4
    Views
    864

    You could just undo the nuts on the front of the...

    You could just undo the nuts on the front of the fulcrum shafts, and the 4 bolts in the top of the diff and the shock bolts. Then wriggle it back by around an inch and a half then lower the whole lot...
  10. Replies
    20
    Views
    1,651

    The Dax VIN for a 1997 std chassis would be...

    The Dax VIN for a 1997 std chassis would be ether:-
    SA9DAXM4RPA038*** or
    SA9DAXM4RRA038***
  11. Thread: Another newbie

    by dave
    Replies
    17
    Views
    2,075

    Hi Steve. Welcome aboard. For a coupe I think...

    Hi Steve.
    Welcome aboard.
    For a coupe I think £30k will be ambitious, but possible with careful planning. As you are not in a hurry to complete the car you will have plenty of time to wait for...
  12. Replies
    13
    Views
    1,509

    As above. I've tested over 100 Dax's and never...

    As above. I've tested over 100 Dax's and never been pulled up on the seatbelt access.
    If you need some advice on your test problems feel free to give me a call. ;-)
  13. Thread: NASCAR belts

    by dave
    Replies
    18
    Views
    1,398

    I find them fine. Not in the way at all....

    I find them fine. Not in the way at all.
  14. Thread: NASCAR belts

    by dave
    Replies
    18
    Views
    1,398

    Not had a problem with them at IVA so far.

    Not had a problem with them at IVA so far.
  15. When I imported a couple of Kirkham's ......

    When I imported a couple of Kirkham's ...
    Turnkey minus. With the engine and gearbox shipped in the same container:-
    Around 5% duty.
    Then 20% VAT on the whole lot.

    I had a stand next to...
  16. Replies
    16
    Views
    5,236

    Bugger. Fat fingers and autocorrect are a bad...

    Bugger. Fat fingers and autocorrect are a bad combination. Lol.
  17. Replies
    16
    Views
    5,236

    Do you unholy the slave cylinder to bleed it?

    Do you unholy the slave cylinder to bleed it?
  18. Replies
    34
    Views
    3,335

    LOL. There's plenty of time to save up for one...

    LOL.
    There's plenty of time to save up for one of mine. ;-)
  19. Here is what commonly happens:- These cars are...

    Here is what commonly happens:-
    These cars are not used regularly.
    If parked the fuel.in the carb will evaporate.
    The float will drop.
    The float bowl needle valve will stick due to a multitude of...
  20. Replies
    10
    Views
    2,076

    38402 On the front of the block next to where...

    38402
    On the front of the block next to where the fuel pump would be mounted there are two tapped (3/8 UNC) bolt holes.
    Often one of these holes is a through hole (into where the fuel.pump pushrod...
  21. Replies
    2
    Views
    996

    Two screws on the front of the carb, with springs...

    Two screws on the front of the carb, with springs under them (angled down at around 45 degrees).
    Turning them clockwise will lean out the mixture at idle.
  22. Thread: Ally bodies

    by dave
    Replies
    36
    Views
    3,696

    Not available as a kit to you..... not until you...

    Not available as a kit to you..... not until you finish that damn Dax. ;-)

    I can sell all individual.parts. but I dont have a build manual etc.
    I have supplied a fair few different people with...
  23. Thread: Ally bodies

    by dave
    Replies
    36
    Views
    3,696

    View Post

    Hmmmm

    www.db427.com

    Thanks for the mentions guys.
  24. 225/65/15 will have the same overall diameter as...

    225/65/15 will have the same overall diameter as the 245/60s you have on the back.
  25. Replies
    22
    Views
    3,975

    Call Ben at Simply Performance Jaguar Spares....

    Call Ben at Simply Performance Jaguar Spares.
    Hell have your diff bolts. ;-)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4