Search:

Type: Posts; User: Lloyd Barnes; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Wanted - FE Cylinder Heads, Edlebrock/Trickflow

    Hi chaps,

    Real long shot, but does anyone have any Edelbrock/Trick Flow cylinder heads for an FE for sale?

    Edelbrock shut up shop earlier this year and moved out of California so there was a 6...
  2. Replies
    632
    Views
    109,493

    That brings back (un)happy memories! I ended up...

    That brings back (un)happy memories! I ended up with the same approach. Get hot, squish to roughly correct shape, enough so they would sit in or near flange shape, tack at 4 points, heat again and...
  3. Replies
    17
    Views
    2,473

    Be interesting to see if more vapour locking...

    Be interesting to see if more vapour locking issues crop up. I'll be hunting down Esso Supreme as well Chris.
  4. Replies
    17
    Views
    2,473

    Is there anywhere you can get information on the...

    Is there anywhere you can get information on the actual percentages in each fuel rather than what they are allowed to use?

    Interesting to note the effect on mixture.....

    Air/fuel ratio...
  5. Replies
    2
    Views
    445

    Real Steel used to do a rubber coated metal...

    Real Steel used to do a rubber coated metal gasket. Not sure if they still do them, and they were a bit more pricey but superb quality. Never leaked and you can keep reusing them
  6. Replies
    10
    Views
    1,442

    Rip the mans arm off at that price for a complete...

    Rip the mans arm off at that price for a complete small block and trans!! :-D
  7. Thread: First run

    by Lloyd Barnes
    Replies
    10
    Views
    806

    Assuming a carb, worth rough setting the idle...

    Assuming a carb, worth rough setting the idle mixture first. I’ve had Holleys out of the box set very lean.
  8. Replies
    26
    Views
    3,656

    Hot dip galvanising is done at around 450...

    Hot dip galvanising is done at around 450 degrees, and will cause deformation which I think is what you may be thinking of? I had a car trailer done and there was some deformation although pretty...
  9. Replies
    6
    Views
    370

    Triumph TR6 possibly?

    Triumph TR6 possibly?
  10. Replies
    31
    Views
    2,431

    Never done the NC500 but the pass of the cattle...

    Never done the NC500 but the pass of the cattle over to Applecross is well worth it. If you are leaving towards the north then the road around the periphery of Applecross is great too. If you are...
  11. Replies
    12
    Views
    892

    The Beetle/Karmann Ghia stalk is the correct...

    The Beetle/Karmann Ghia stalk is the correct part, I think the later 427s having the one with the momentary switch to switch the headlight dim/dip via a relay. If you do use that, be aware that if...
  12. Replies
    16
    Views
    1,327

    Nope Kev, I'm just out of touch ;-) that's why...

    Nope Kev, I'm just out of touch ;-) that's why Anthony is testing the car for me! :-D
  13. Replies
    16
    Views
    1,327

    Unless times have changed, you can't drive it for...

    Unless times have changed, you can't drive it for its DVLA check though. Is that still the same?
  14. Replies
    4
    Views
    620

    Me too, great bunch of lads. Fun to watch them...

    Me too, great bunch of lads. Fun to watch them blow my Galaxies onto the rims with the blaster!
  15. Replies
    31
    Views
    8,149

    Rare old motor, only produced for a few years. ...

    Rare old motor, only produced for a few years.

    You'd have to bore it around 125 thou to get to 335 which sounds unlikely? Possibly it has a crank out of a 350 it in with a light rebore. No idea...
  16. Replies
    16
    Views
    3,774

    Oh, no! Aaron, it’s gonna eyed to be built as a...

    Oh, no! Aaron, it’s gonna eyed to be built as a hybrid at this rate?!
    I can’t talk, 10 years so far on the Crendon!
  17. Replies
    17
    Views
    1,493

    An interesting topic. If you’re ever near...

    An interesting topic. If you’re ever near Snowdonia, I highly recommend a tour around “electric mountain”. Essentially a huge battery to supply power at peak demand times. Nett consumer of...
  18. Replies
    13
    Views
    1,153

    I’m pretty confident the first car didn’t...

    I’m pretty confident the first car didn’t exist in 1965 or for many years after that.
  19. Replies
    13
    Views
    1,153

    Why do they insist on calling these cars 1965...

    Why do they insist on calling these cars 1965 when they were made many years later?! The advert is happy to let you think it is an original.
  20. Replies
    16
    Views
    3,774

    I thought Simon had a loan set of radiused nuts...

    I thought Simon had a loan set of radiused nuts that people used for IVA?
  21. Replies
    17
    Views
    1,493

    Any scientists on here? I thought crude was...

    Any scientists on here?
    I thought crude was fractionated into everything from bitumen through fuel oil for ship, avgas and finally heating gas. Can you stop producing petrol and diesel without...
  22. Replies
    6
    Views
    454

    As above, just run a tap down the threads. Good...

    As above, just run a tap down the threads. Good practice for any thread in your rebuild.
  23. Replies
    62
    Views
    7,394

    I think I must be unique. Have had a couple of...

    I think I must be unique. Have had a couple of Range Rovers with very few issues. However don't get me started on Fords! We have three leased through work, couple of Rangers and a Focus. What a...
  24. Replies
    7
    Views
    804

    £70 for the test and it doesn't look terribly...

    £70 for the test and it doesn't look terribly onerous. Nothing like the car test. TBH, if you've built it properly and used a bit of common sense its going to pass.

    I built one with a friend a...
  25. Replies
    11
    Views
    727

    Container rates from far east have gone from...

    Container rates from far east have gone from around £3-4k up to £8.5-12k for a 40ft in a matter of months. The reduction in manufacturing in Europe plus high European demand has meant they can't...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4