Search:

Type: Posts; User: Robin427; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    1,727

    Not far from me, then!

    Not far from me, then!
  2. Replies
    9
    Views
    1,727

    Anyone left in East Sussex?

    Not much activity on this forum recently. Anyone up for organising a drive out? Rather than the same old Grasshopper meet thought varying it a bit would be preferable
  3. Replies
    27
    Views
    3,415

    Hardly likely to use live ones! Wheel had...

    Hardly likely to use live ones!

    Wheel had first proper outing this morning. The boss is rubbing so I've ground the escutcheon down more and won't have the adjuster full back
  4. Replies
    11
    Views
    1,636

    Took her for a blast today - temperatures stayed...

    Took her for a blast today - temperatures stayed really low, much lower than they had been, but then I have proper coolant in the system and no leaks, fingers crossed. Wasn't that hot today, I...
  5. Replies
    27
    Views
    3,415

    Horn adaptor printed (using 22LR shell cases as...

    Horn adaptor printed (using 22LR shell cases as contacts) - works fine!

    38845
  6. Replies
    11
    Views
    1,636

    I haven't driven mine since fitting the new cap,...

    I haven't driven mine since fitting the new cap, apart from moving it around on the drive. Taxing it tomorrow and going for a nice drive to see how the new steering wheel behaves
  7. Replies
    27
    Views
    3,415

    Well, it arrived today, incredibly quickly!...

    Well, it arrived today, incredibly quickly! Fortunately, my adaptor (Raid 76mm to Momo 70mm) had arrived, so I thought bolting it up would be a simple job.

    Sadly not... the adaptor arrived with M5...
  8. Replies
    27
    Views
    3,415

    Great minds!

    Great minds!
  9. Replies
    17
    Views
    1,437

    My roll of TPU arrived and after printing a...

    My roll of TPU arrived and after printing a little mod for the extruder with ABS (to stop it bunching up) I set about printing that door seal. Printed perfectly and it's INCREDIBLY tough. Been...
  10. Replies
    27
    Views
    3,415

    Old thread but just ordered one of these....

    Old thread but just ordered one of these. Fortunately I noticed that the bolt pattern was different to my Raid steering wheel and after some research I found that the PCD on the Raid is 74mm whereas...
  11. Replies
    17
    Views
    1,437

    Never tried ASA or Polypropylene but there's no...

    Never tried ASA or Polypropylene but there's no space with the door shut - seal fully compressed. Yours looks great, colour aside :-)
  12. Replies
    0
    Views
    446

    Roll bar grommet/escutcheon - 3D printed

    38840

    Don't know if the attachment works but I printed and fitted some grommet covers for the roll bars. Should keep them in place and I think they look better than what was there before (as I'd...
  13. Replies
    17
    Views
    1,437

    Not a bad idea. I've ordered some flexible...

    Not a bad idea. I've ordered some flexible filament today which might also work
  14. Replies
    17
    Views
    1,437

    For a company who is fiercely proud of their...

    For a company who is fiercely proud of their brand, they don't seem to mind them all driving around looking unfinished. If you want some, just let me know
  15. Replies
    17
    Views
    1,437

    That makes one of us... :(

    That makes one of us... :(
  16. Replies
    17
    Views
    1,437

    I changed my bed levelling to 3 point. I think...

    I changed my bed levelling to 3 point. I think that helped.
  17. Replies
    17
    Views
    1,437

    I certainly did! On the same listing:...

    I certainly did! On the same listing: https://www.thingiverse.com/thing:4545679
    However, despite hours of sanding, polishing and lacquering, I found they were smashed the first time the door shut -...
  18. Replies
    0
    Views
    372

    Boot seal finisher, 3D printed

    Continuing with my 3D printed theme for Cobra bits, when I was loading some tools into the boot to keep them off the floor overnight, I noticed that where the seals meet in the middle, just behind...
  19. Thread: 3D Printers

    by Robin427
    Replies
    16
    Views
    3,118

    Acetone smoothing can be quite effective but you...

    Acetone smoothing can be quite effective but you can lose dimensional accuracy and it can weaken prints.
    I've tried hairspray, ABS juice and wide brims to try and make Nylon stick but to no effect....
  20. Replies
    0
    Views
    377

    Roll bar grommet/escutcheon - 3D curve

    The outer roll bar (Mk.3) sits in a curve in the bodywork. To get a flat escutcheon to fit, one would need to make it oval but I'm thinking about 3D printing escutcheons which won't necessarily flex...
  21. Thread: 3D Printers

    by Robin427
    Replies
    16
    Views
    3,118

    I bought loads of PETG but for the bits I was...

    I bought loads of PETG but for the bits I was producing, the stringing meant far too much post processing so I don't use it so much any more.
    My printer is in my workshop so the fumes aren't an...
  22. Thread: 3D Printers

    by Robin427
    Replies
    16
    Views
    3,118

    Yes, found a glass front cabinet that fitted my...

    Yes, found a glass front cabinet that fitted my printer and it has a heater in there too for the winter months as otherwise the printer throws an error when it's trying to heat up.

    I still get...
  23. Replies
    17
    Views
    1,437

    Please post a make on Thingiverse! So few people...

    Please post a make on Thingiverse! So few people do...
  24. Replies
    17
    Views
    1,437

    Door end seals (3D printed)

    Andy never responded to my e-mail regarding the trim finishing pieces that cover the door seal ends so I designed and printed my own. It's a plastic car and a plastic door seal so I'm not worried...
  25. Thread: 3D Printers

    by Robin427
    Replies
    16
    Views
    3,118

    Don't know why I didn't think of printing parts...

    Don't know why I didn't think of printing parts for my Cobra before - I've had a 3D printer for a couple of years now (Wanhao i3+). I was using OpenSCAD to design but have now switched to FreeCAD...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4