Search:

Type: Posts; User: dave; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Thread: NASCAR belts

    by dave
    Replies
    18
    Views
    1,040

    I find them fine. Not in the way at all....

    I find them fine. Not in the way at all.
  2. Thread: NASCAR belts

    by dave
    Replies
    18
    Views
    1,040

    Not had a problem with them at IVA so far.

    Not had a problem with them at IVA so far.
  3. When I imported a couple of Kirkham's ......

    When I imported a couple of Kirkham's ...
    Turnkey minus. With the engine and gearbox shipped in the same container:-
    Around 5% duty.
    Then 20% VAT on the whole lot.

    I had a stand next to...
  4. Replies
    16
    Views
    3,142

    Bugger. Fat fingers and autocorrect are a bad...

    Bugger. Fat fingers and autocorrect are a bad combination. Lol.
  5. Replies
    16
    Views
    3,142

    Do you unholy the slave cylinder to bleed it?

    Do you unholy the slave cylinder to bleed it?
  6. Replies
    34
    Views
    2,235

    LOL. There's plenty of time to save up for one...

    LOL.
    There's plenty of time to save up for one of mine. ;-)
  7. Here is what commonly happens:- These cars are...

    Here is what commonly happens:-
    These cars are not used regularly.
    If parked the fuel.in the carb will evaporate.
    The float will drop.
    The float bowl needle valve will stick due to a multitude of...
  8. Replies
    10
    Views
    1,357

    38402 On the front of the block next to where...

    38402
    On the front of the block next to where the fuel pump would be mounted there are two tapped (3/8 UNC) bolt holes.
    Often one of these holes is a through hole (into where the fuel.pump pushrod...
  9. Replies
    2
    Views
    611

    Two screws on the front of the carb, with springs...

    Two screws on the front of the carb, with springs under them (angled down at around 45 degrees).
    Turning them clockwise will lean out the mixture at idle.
  10. Thread: Ally bodies

    by dave
    Replies
    36
    Views
    2,702

    Not available as a kit to you..... not until you...

    Not available as a kit to you..... not until you finish that damn Dax. ;-)

    I can sell all individual.parts. but I dont have a build manual etc.
    I have supplied a fair few different people with...
  11. Thread: Ally bodies

    by dave
    Replies
    36
    Views
    2,702

    View Post

    Hmmmm

    www.db427.com

    Thanks for the mentions guys.
  12. 225/65/15 will have the same overall diameter as...

    225/65/15 will have the same overall diameter as the 245/60s you have on the back.
  13. Replies
    22
    Views
    2,210

    Call Ben at Simply Performance Jaguar Spares....

    Call Ben at Simply Performance Jaguar Spares.
    Hell have your diff bolts. ;-)
  14. Replies
    301
    Views
    35,487

    Now, if there was just someone out there who made...

    Now, if there was just someone out there who made a Cobra that you didn't have to modify Cobra parts in order for them to fit????? :rolleyes:;-)
  15. Thread: IVA overriders

    by dave
    Replies
    39
    Views
    3,135

    But you said "Why cheat when you can comply" I...

    But you said "Why cheat when you can comply"

    I don't use over riders too often these days.
    The rear nudge bar is good for hanging the extra lights and reflectors from for the test.
    I use the...
  16. Thread: IVA overriders

    by dave
    Replies
    39
    Views
    3,135

    Sorry to be the bearer of bad news, but these...

    Sorry to be the bearer of bad news, but these look like they will fail.
    Where your insert meets the edge of the over rider there needs to me a minimum 5mm radius. It looks like and angle from the...
  17. Replies
    13
    Views
    1,361

    Tax is now £265 First reg fee is still £55

    Tax is now £265
    First reg fee is still £55
  18. Replies
    13
    Views
    1,361

    Make sure you send by "Royal Mail Special...

    Make sure you send by "Royal Mail Special Delivery"
    As they will probably try to say they never received it when you chase them up in two weeks to find out why you havent had a V5 come through....
  19. Replies
    30
    Views
    2,970

    Aaron: Yes, you understood correctly. ...

    Aaron:
    Yes, you understood correctly.

    Drammyboy:
    The Diff in Aaron's car is not attached to the suspension arms. So will not be a problem.
  20. Replies
    30
    Views
    2,970

    If you can:- Set the engine and box that suits...

    If you can:-
    Set the engine and box that suits the chassis/tunnel best.
    Make sure they are as "north/south" as possible.
    Then, consider modifying the upper diff mount (make a new one possibly) so...
  21. Replies
    18
    Views
    4,784

    You missed a digit out. Its registration is FNB...

    You missed a digit out.
    Its registration is FNB 149C
    Regs as a 1965 Hi Tech.....
    Not that they were in business in 1965.
  22. Replies
    14
    Views
    1,303

    That 0.9mm is a lot harder to fold than 0.7mm.......

    That 0.9mm is a lot harder to fold than 0.7mm.... been there!!! :-(
  23. Replies
    14
    Views
    1,303

    If you do go for stainless. Get 430 Bright...

    If you do go for stainless. Get 430 Bright Annealed. 0.7mm is much easier to fold than anything thicker.
  24. Replies
    14
    Views
    1,303

    1.5mm will be fine. 1050 H14 grade should be...

    1.5mm will be fine.
    1050 H14 grade should be fine for what you mention.
    If you are polishing it, then you can wax it to protect against corrosion.
  25. Replies
    61
    Views
    4,874

    Out dragging a Fiesta is unlikely to be an option...

    Out dragging a Fiesta is unlikely to be an option with a tired Rover V8....
    ... or are you going to fit it with a new "£££" cam?..... or maybe pester someone who it trying to earn a living to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4