Search:

Type: Posts; User: peterj1974; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    84

    Ak Gen 2 Front Lower wishbone bushes

    Hi
    Had first MOT on Friday and tester discovered that both front lower wishbone bushes are shot and need replacing.
    He advised to fit some poly bushes and recommended superflex.
    Has any one used...
  2. Replies
    20
    Views
    1,852

    Hello So still not fixed the issue but have a...

    Hello
    So still not fixed the issue but have a bit more info to run past the forum and see what you think.
    I've fixed the leaky oil sender with some permatex thread sealant. I changed the oil and...
  3. Thread: Brake Issue

    by peterj1974
    Replies
    10
    Views
    513

    Try a dowty washer. Worked for me when my brake...

    Try a dowty washer. Worked for me when my brake flexie connection was weeping on calliper connection
  4. Replies
    3
    Views
    281

    Nice one all done now. Cheers

    Nice one all done now. Cheers
  5. Replies
    7
    Views
    298

    You can get the correct gauge from merlin...

    You can get the correct gauge from merlin motorsport or demon tweeks. Get the smiths one
  6. Replies
    3
    Views
    281

    Hi Paul I’ve got it all the way down but still...

    Hi Paul
    I’ve got it all the way down but still feels there’s some compression. I’m trying to get the spring off so I can fit the spacer to it. I’ll have another go

    Cheers
    Pete
  7. Replies
    3
    Views
    281

    Spring compressor

    I have the gaz shocks supplied by AK on my gen 2. I bought a spring compressor from Halfords with double hooks on each end. The problem is I can only get one hook in and even then it doesn’t seem...
  8. Replies
    0
    Views
    164

    Vintage wheels tyre valves

    Hi
    I’m running vintage wheels 407s on my AK. The tyre valves I’ve got have started to split along the base of the rubber. So I’m looking to replace them with some metal ones. Anyone know if...
  9. Replies
    20
    Views
    1,852

    Hello Did some checks over the weekend. Oil...

    Hello
    Did some checks over the weekend.
    Oil level is fine. Coolant looked okay - I use the AK coolant tank, it was about half full - so I added a bit more coolant.
    I bough an oil pressure test kit...
  10. Replies
    6
    Views
    684

    chevy 350 oil leak

    Hi
    I've noticed oil the top of my chevy 350, just under the dizzy. I ran it up to temp on the weekend and can see that it's coming out of the connection where you take the oil pressure.
    I'm using a...
  11. I have an AK and whilst building the car used...

    I have an AK and whilst building the car used jack and axle stands. I’ve recently bought a mid rise scissor lift and it’s much better. Wish I’d bought one earlier
  12. Hi Steve, I’m in Runcorn and completed an AK...

    Hi Steve, I’m in Runcorn and completed an AK earlier this year. You’re more than welcome to come and take a look. Cheers Pete
  13. Replies
    21
    Views
    1,834

    Mine arrived too. Thanks a lot

    Mine arrived too. Thanks a lot
  14. Replies
    7
    Views
    511

    I went with 35mm cable and it’s been fine. This...

    I went with 35mm cable and it’s been fine. This is higher rated than what AK recommend and fits fine. Bought mine from 12volt planet
  15. Replies
    20
    Views
    1,852

    Hi Mike Pressure testing kit sounds good....

    Hi Mike
    Pressure testing kit sounds good. Wouldn’t mind getting one myself. Which one have you got?
  16. Replies
    20
    Views
    1,852

    Thanks Lee. I’ll take you up on the offer. Will...

    Thanks Lee. I’ll take you up on the offer. Will give you a call later
  17. Replies
    20
    Views
    1,852

    was showing 0.5 to 1 bar when running at 2000 rpm

    was showing 0.5 to 1 bar when running at 2000 rpm
  18. Replies
    20
    Views
    1,852

    Hi - It's a chevy 350 and showing 0.5 to 1 bar

    Hi - It's a chevy 350 and showing 0.5 to 1 bar
  19. Replies
    20
    Views
    1,852

    Low oil pressure

    Took the car out on Sunday for a run and noticed oil pressure seemed low. Was running at 0.5 to 1 bar. Engine was at temperature.
    Seems low to me. Any ideas?
    Cheers
    Pete
  20. Replies
    21
    Views
    1,834

    Hi I’ll take a pair please. Can you pm me your...

    Hi
    I’ll take a pair please. Can you pm me your email. Is PayPal ok?

    Thanks

    Pete
  21. Replies
    36
    Views
    2,961

    Hello Further update on the lift - so turns out...

    Hello
    Further update on the lift - so turns out there was an issue with the lift. I have to say Automotech were fantastic and fixed the lift the next day.
    The issue was with the ratchet system - on...
  22. Replies
    9
    Views
    552

    I have the same pump. The push on connections on...

    I have the same pump. The push on connections on mine weren’t great and could work loose. Make sure they’re pushed on. I made a L shaped bracket to keep them pushed on
  23. Replies
    36
    Views
    2,961

    Update on scissor lift. It was delivered on...

    Update on scissor lift.
    It was delivered on Tuesday but only got around to setting it up today. I went for the Automotech AS7530D, and also opted for the low profile loading ramps they sell.
    I'm...
  24. Replies
    30
    Views
    1,493

    Looks fantastic. The iva is still fresh in my...

    Looks fantastic. The iva is still fresh in my mind so if you want a chat about what to watch out for drop me a message.

    Cheers
    Pete
  25. Replies
    36
    Views
    2,961

    I’ve now ordered the automotech AS7530. It...

    I’ve now ordered the automotech AS7530.
    It arrives on Tuesday so I’ll post some pics and initial thoughts.
    The strongman I thought might be a bit too long for the AK. It was also the most...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4