Search:

Type: Posts; User: peterj1974; Keyword(s):

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    121

    Blue with white stripe on M5

    Between j7 and 8 about midday today.
    Sounded great
  2. Thread: Door Locks

    by peterj1974
    Replies
    3
    Views
    302

    I used the stainless steel tube approach as well

    I used the stainless steel tube approach as well
  3. Thread: Tilt Lift

    by peterj1974
    Replies
    6
    Views
    572

    Hi Alex Sent you a pm Cheers Pete

    Hi Alex
    Sent you a pm
    Cheers
    Pete
  4. Replies
    33
    Views
    3,614

    That’s a great achievement Andy. Both in time...

    That’s a great achievement Andy. Both in time and cost. I added my Ak cost up and it comes to 45k. With hindsight I reckon I could have saved 5k along the way in various places but to do it all for...
  5. Thread: Tilt Lift

    by peterj1974
    Replies
    6
    Views
    572

    Hi Alex I’m interested. What make and model is...

    Hi Alex
    I’m interested. What make and model is it?
    Thanks
    Pete
  6. Replies
    9
    Views
    641

    I didn’t fit them on my gen2 and passed iva...

    I didn’t fit them on my gen2 and passed iva with no problems
    Pete
  7. I’ve gone for 10mm and that’s been fine

    I’ve gone for 10mm and that’s been fine
  8. Replies
    9
    Views
    755

    Hi Alan Sent you a PM Cheers Pete

    Hi Alan
    Sent you a PM
    Cheers
    Pete
  9. Replies
    26
    Views
    1,733

    I had a taping noise on my Chevy 350. Turned out...

    I had a taping noise on my Chevy 350. Turned out to be a worn pushrod due to oil starvation to the rod.
  10. Replies
    3
    Views
    410

    So I’ve managed to route the leads better by...

    So I’ve managed to route the leads better by adapting the ht lead holder I had to run vertical along the rocker cover. This pulls the leads away from the headers more and gives much better...
  11. Hi Mike I used similar boots. Mine were made by...

    Hi Mike
    I used similar boots. Mine were made by DEI. They’re no good if they touch the header. They transfer the heat to the cable which then burns. I’m working on better cable routing using a...
  12. Replies
    3
    Views
    410

    Wrapping camcoated header

    Hi
    I had a headers camcoated but have had issues with ht leads touching the headers and burning through. I’m now thinking of wrapping the headers with some dei titanium exhaust wrap from demon...
  13. Hi Steve Could you post a pic of how yours are...

    Hi Steve
    Could you post a pic of how yours are run?
    Cheers Pete
  14. Ignition lead heat protection on AK with Chevy 350

    Hi,
    I've just had an ignition lead burn through on my AK. I've got a chevy 350 and AK headers. On the drivers side a number of the ignition leads are very close to the headers so I fitted some heat...
  15. Replies
    1
    Views
    252

    Underbody rust protection

    Hi
    Only done 250 miles since passing IVA and already noticing rust on the chassis where stones have chipped the powder coat.
    Has anyone got any experience or feedback on some form of underbody...
  16. Replies
    3
    Views
    354

    C Spanner size for GAZ shocks

    Hi
    Does anyone know the correct C spanner size to adjust the GAZ shocks on an AK?

    Cheers

    Pete
  17. Hi I had the same concerns with my dash and Iva....

    Hi
    I had the same concerns with my dash and Iva. Yours looks much neater than mine and I passed with no issues. Just make sure there are no loose wires dangling down and you’ll be fine.
    Cheers...
  18. Thread: Heat!

    by peterj1974
    Replies
    8
    Views
    397

    Hi. I have the same engine and ended up getting...

    Hi. I have the same engine and ended up getting my headers camcoated. Made a big difference to heat in engine bay. Also put some heat proof boots on the plug ends.
    Cheers
    Pete
  19. Replies
    2
    Views
    292

    Garage recommendations in North West

    Hi
    Can anyone recommend a garage for getting some work done on my cobra - in or around North West.
    Looking for someone who is familiar with working on Cobras and american V8s. (Think my gearbox...
  20. Replies
    2
    Views
    253

    That’s the one - thanks a lot

    That’s the one - thanks a lot
  21. Replies
    2
    Views
    253

    Smiths gauges electrical connector

    Hi
    Does anyone know what this type of electrical connector block is - from a smiths flight gauge3731937319

    Thanks

    Pete
  22. Thread: Wiper motor

    by peterj1974
    Replies
    2
    Views
    248

    Hi SVC have a diagram. I followed this set up...

    Hi
    SVC have a diagram. I followed this set up
    https://www.s-v-c.co.uk/wiper-systems/

    Cheers

    Pete
  23. Replies
    6
    Views
    517

    Use an enamel based paint. You can get little...

    Use an enamel based paint. You can get little pots from b and q. I tried black chassis paint and it was too thin to cover properly. Paint from the inside as well and ensure you get full coverage On...
  24. Replies
    3
    Views
    336

    Suspension geometry/corner weights etc

    Hi,
    I've had the tracking sorted on my AK gen 2 but was thinking of taking the car somewhere to get he suspension and overall geometry of the car checked.
    I don't know much about this - but have...
  25. Replies
    5
    Views
    303

    Don't seem to be able to send you a PM. Can you...

    Don't seem to be able to send you a PM.
    Can you PM me your email

    Thanks

    Pete
Results 1 to 25 of 459
Page 1 of 19 1 2 3 4