Search:

Type: Posts; User: alunwill; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    162

    Hi Graham, Yes those are the ones. The...

    Hi Graham,

    Yes those are the ones.

    The toyota part numbers, which rockauto uses are below

    top- 23250B (O ring to fuel rail)
    Middle - 23250C (vibration ring, I think that's what they call...
  2. Replies
    3
    Views
    162

    1uzfe injector seals

    I serviced my injectors a few months ago, replacing all the seals and o rings, together with checking spray patterns but I've had an annoying rough running when I put my foot down. It passed the...
  3. Thread: Megasquirt

    by alunwill
    Replies
    2
    Views
    505

    Thanks Martin, All sorted, I just wasn't...

    Thanks Martin,

    All sorted, I just wasn't looking in the right place


    Many thanks
  4. Thread: Megasquirt

    by alunwill
    Replies
    2
    Views
    505

    Megasquirt

    does anyone have an electronic version of the ms3 manual I could have
  5. Replies
    7
    Views
    472

    Yes I understand the sentiment but second time...

    Yes I understand the sentiment but second time around and 1/4 of the size should reduce it to 2 yrs surely.
  6. Replies
    7
    Views
    472

    That's a nice unit. Where did you get the kit from

    That's a nice unit. Where did you get the kit from
  7. Replies
    7
    Views
    472

    Junior size cobra

    I've been looking for a junior size cobra for my grandson, 5 years old . I'm interested in a kit not the finished article. Any ideas if they are available. Thought I'd try here before I trawl the net
  8. Replies
    3
    Views
    546

    I'd say you were unlucky. Either that or you've...

    I'd say you were unlucky. Either that or you've been switching off whilst on full load which is unlikely to happen. Not sure what size starter motor and alternator you have but that's about the only...
  9. Replies
    14
    Views
    1,173

    One thought, what's the height of your engine...

    One thought, what's the height of your engine mounts. Is the clearance issue linked to hitting the chassis side rail, front to rear.
  10. Replies
    14
    Views
    1,173

    As Tony said, I used a saab pump which had the...

    As Tony said, I used a saab pump which had the same pulley rib as the lexus. Reversed the tensioner and put the alternator on the opposite side of the engine in place of the ac compressor. Had no...
  11. Replies
    16
    Views
    1,901

    It's just the amount of peripheral bits which you...

    It's just the amount of peripheral bits which you need to take off that takes the time òn a Lexus. Driver side a bit o of a pain because of the air input manifold.
  12. Replies
    5
    Views
    624

    It's a while since I put mine together but from...

    It's a while since I put mine together but from memory I think you calibrate the gauge which produces one table and then you calibrate the sender with the fuel, which produces another table. It then...
  13. Replies
    5
    Views
    624

    I installed a vdo and spider. Both work fine...

    I installed a vdo and spider. Both work fine together and far better than the caerbont float style. Just take your time calibrating it. As for compatability with the smiths gauges, I had no issues....
  14. Thread: Ecm choice

    by alunwill
    Replies
    5
    Views
    740

    Ecm choice

    with so many ecms on the market, what are people using and what's the experience regarding installation. Specifically fuel maps etc, installation manuals, UK support and ease of software use
  15. Replies
    3
    Views
    630

    Graham Check out rock auto in the state's. ...

    Graham

    Check out rock auto in the state's. When you take the cost of the components and postage together they normally come in quite reasonable. In fact I had a couple of gaskets delivered for...
  16. Thread: Radiators

    by alunwill
    Replies
    10
    Views
    1,596

    Graham,, What size hole do those grommets from...

    Graham,,
    What size hole do those grommets from trimmer bros need to fit
  17. Thread: Spa gauge

    by alunwill
    Replies
    0
    Views
    280

    Spa gauge

    Has anyone bought one of the spa dual temperature gauges, oil/water. If so do they supply thermistor sensors (normal type) or the super accurate thermocouple as standard when you buy one.

    Thanks
  18. Replies
    17
    Views
    1,824

    I wouldn't bother with them. About the only...

    I wouldn't bother with them. About the only useful fuel sender is a vdo type unit linked to a gauge wizard
  19. Thread: Radiators

    by alunwill
    Replies
    10
    Views
    1,596

    Stephen, Looking at the mustang rads are the...

    Stephen,

    Looking at the mustang rads are the inlet/outlets on the same side or opposites. Also does it have the oil cooler option for an auto box
  20. Thread: Radiators

    by alunwill
    Replies
    10
    Views
    1,596

    Radiators

    Had my radiator pop yesterday.

    What's the current thought on rads for an AK.

    I've got a copper sd1 fitted at the moment which was a refurb from grantham radiators. I'm looking for an ally one...
  21. Replies
    41
    Views
    3,316

    Brazing aluminium

    I'm thinking of doing a bit of aluminium brazing. Any advice regarding the best rods to buy and general tips on what not to do.
  22. Replies
    18
    Views
    1,521

    Yes local scrappies are around. I found one close...

    Yes local scrappies are around. I found one close to me by just googling. I think we've all moved to finding everything on fleabay as first port of call . The 1992 one that's on offer from Ian may be...
  23. Replies
    18
    Views
    1,521

    Probably just as cheap to get an old unit from...

    Probably just as cheap to get an old unit from the local scrappy.

    The bearings are:
    Original are koyo 689ru and 61801ru.

    I bought replacements from simply bearings. Plenty of choice but I...
  24. Lexus users: What a change - refurbed IAC fitted

    I fitted a refurbed IAC to my lexus 1uzfe today. What a difference it's made.

    At the end of last season, I noted a slight issue with idling. This year it moved into rough running.

    My initial...
  25. I tried a number of ausi and nz take of designs...

    I tried a number of ausi and nz take of designs and threw them all in the bin because of oil leaks. Non of them sealed properly. In the end I modified the standard Lexus filter plate. Cut it down the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4