Search:

Type: Posts; User: Peaches94; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    1,150

    Hi Craig, I can’t remember if front or rear,...

    Hi Craig, I can’t remember if front or rear, but the gauge the tester used was small enough to check both ends.

    ps. If you are off to Kidderminster remember to check seat base to top seat belt...
  2. Replies
    20
    Views
    1,150

    I has closed back over riders fitted for my first...

    I has closed back over riders fitted for my first IVA test at Kidderminster and these failed on radius. This despite being declared IVA safe by Europa. Funnily enough they were not fitted for the...
  3. Thread: HT leads

    by Peaches94
    Replies
    8
    Views
    557

    mine passed IVA with something similar to this....

    mine passed IVA with something similar to this.
    your critical issue is making sure there’s no chance of leads burning on headers
  4. Replies
    6
    Views
    390

    From what I remember you end up cutting off the...

    From what I remember you end up cutting off the bmw connectors and making up some new ones using the connectors supplied with the AK loom. There are quite a few of the column wires that don’t get...
  5. Replies
    14
    Views
    592

    I made some split washers out of aluminium sheet....

    I made some split washers out of aluminium sheet. Easy to Spring over the steering arm and no chance of falling off.
  6. Replies
    9
    Views
    523

    Unsure why it’s stopped working but, just to...

    Unsure why it’s stopped working but, just to confirm my similar unit runs constantly.
  7. Thread: Scissor lift

    by Peaches94
    Replies
    36
    Views
    2,927

    good to hear it worked for you. I followed the...

    good to hear it worked for you. I followed the advice of the supplier who advised that they had installations that popped standard breakers hence they recommended 16A ‘c’ curve that apparently...
  8. Thread: Scissor lift

    by Peaches94
    Replies
    36
    Views
    2,927

    agree with Paul. I have one and it’s a great...

    agree with Paul. I have one and it’s a great bit of kit. Don’t forget to factor in transport costs and even though they are single phase, you will need to change the relevant circuit breaker to a...
  9. Replies
    8
    Views
    916

    I think I’d be trying to get it aligned as best...

    I think I’d be trying to get it aligned as best as possible, main reason being if it’s slightly off, then it can have an impact on where the exhausts exit assuming using side pipes.
    Others may...
  10. Replies
    8
    Views
    782

    Hi sorry about the delay. 37785 My Carter...

    Hi sorry about the delay.
    37785

    My Carter pump can just be seen to the left of the water bottle. Its actually mounted as low down as possible.
    Hope this helps
  11. Replies
    8
    Views
    782

    Fitted my pump in the engine bay, low down by...

    Fitted my pump in the engine bay, low down by transmission tunnel, near side. Works a treat. Will see if I have a photo.
  12. Another vote for Hylomar

    Another vote for Hylomar
  13. Thread: Door Locks

    by Peaches94
    Replies
    3
    Views
    549

    Craig, I used a section of stainless steel tube...

    Craig, I used a section of stainless steel tube where you have the lock nut. This allows the metal strap to sit closer to the fibreglass and it bolts up nice an tight.
  14. Replies
    12
    Views
    1,551

    I’ve got some stick on wheelarch spats you can...

    I’ve got some stick on wheelarch spats you can have for the cost of postage. You just need to source some double sided 3m tape. PM me if of any use.
  15. Replies
    8
    Views
    719

    Could be the float/needle valve isn’t seating...

    Could be the float/needle valve isn’t seating correctly and carb is flooding when under pressure from fuel pump. Is the fuel pump electric or engine driven?
  16. 37524 Hi Pete, old photo here, will try and...

    37524

    Hi Pete, old photo here, will try and get a clearer one.
  17. Hi Pete, I run my plug leads below the headers...

    Hi Pete, I run my plug leads below the headers rather than dropping down in between. I’ve got same heat boots and some are definitely touching headers. No problem thus far but think i’ll be...
  18. Replies
    2
    Views
    399

    Rear arch protection

    Has anyone had any success with clear arch protectors instead of the usual stainless jobs?
    if yes, where did you source them from?
    Ive tried a couple of local wrappers but they only seem interested...
  19. Replies
    7
    Views
    775

    Hi Craig, I used some body filler from...

    Hi Craig, I used some body filler from Toolstation, Think it was called Big Boy !. Seems to have done the trick and I also used it for sticking some cable ties under the wings. All still in place.
  20. Replies
    7
    Views
    775

    Definitely a real spider!

    Definitely a real spider!
  21. Replies
    7
    Views
    775

    Here’s how mine went ...

    Here’s how mine went

    http://www.cobraclub.com/forum/attachment.php?attachmentid=37424&stc=1
  22. Replies
    9
    Views
    1,346

    Just resurrecting this thread with a bit of...

    Just resurrecting this thread with a bit of feedback on running these gauges for a while and its all been quite positive. Very easy to install and calibrate and, if you need it, support is lifetime...
  23. Thread: Gas Rams

    by Peaches94
    Replies
    4
    Views
    500

    Self tapper screws works for me. Plenty strong...

    Self tapper screws works for me. Plenty strong enough so far.
  24. Replies
    10
    Views
    717

    Well done - it’s a great feeling.

    Well done - it’s a great feeling.
  25. Thread: IVA pass

    by Peaches94
    Replies
    12
    Views
    1,139

    Excellent - well done

    Excellent - well done
Results 1 to 25 of 248
Page 1 of 10 1 2 3 4