Search:

Type: Posts; User: Cobragreyhead; Keyword(s):

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    247

    Weiand inlet manifold

    Weiand SBF 8011 inlet manifold never used by me, blasted, very good condition with wedge plate £150 plus postage
  2. Replies
    30
    Views
    4,611

    Are they not earthed through the mounting bolts...

    Are they not earthed through the mounting bolts to chassis?
  3. Yes ditto, mine were tight on car 1, but loose on...

    Yes ditto, mine were tight on car 1, but loose on car 2, for reasons unknown so locktited on as per ward
  4. Replies
    31
    Views
    6,095

    So do we use Max bhp OR max torque lbs/ft for...

    So do we use Max bhp OR max torque lbs/ft for the engine power figure?
  5. Replies
    44
    Views
    3,003

    eal (replica) No sold to price williams tutor...

    eal (replica)
    No sold to price williams tutor at Eton circa ‘96

    This made way for the Dennis Adams Jaguar based roadster that we still have in the collection
  6. Replies
    44
    Views
    3,003

    Teal (replica) No sold to price williams tutor...

    Teal (replica)
    No sold to price williams tutor at Eton circa ‘96

    This made way for the Dennis Adams Jaguar based roadster that we still have in the collection
  7. Replies
    4
    Views
    278

    Yeah go with jon if dax loom, i have a Premier...

    Yeah go with jon if dax loom, i have a Premier wiring loom and there is a difference between the early(yours ) horn on stalk and the later horn on wheel they way that the supplies are pos or neg from...
  8. Replies
    16
    Views
    765

    Yes and that dax rad is pretty low with that...

    Yes and that dax rad is pretty low with that valance too, i raised my rad with a slight tilt to have that improvement
  9. Replies
    44
    Views
    3,003

    Yeah been there once its great, my dad also went...

    Yeah been there once its great, my dad also went there with teal bugatti owners club and theres a black and white photo of dads type 35 on the bank there, circa ,96, try and find a photo.
  10. Replies
    18
    Views
    1,439

    I have a 3t scissor. 1 metre height underneath ,...

    I have a 3t scissor. 1 metre height underneath , perfect for me as any higher and ceiling an issue.
  11. Replies
    27
    Views
    2,390

    Well at least it was a lot of lockdown excitement...

    Well at least it was a lot of lockdown excitement for everyone wasnt it!
  12. Replies
    45
    Views
    1,970

    If you wind in both idle screws the engine should...

    If you wind in both idle screws the engine should cut out, if it doesnt and idles normal then you have another issue, like i did.

    also worth checking that bas plate is straight and not warped. And...
  13. Replies
    45
    Views
    1,970

    Ditto the above, just rebuilt mine an idles...

    Ditto the above, just rebuilt mine an idles lovely. One other thing if you have excessive co 2 on idle like i did check the idle transfer slot exposure measurement thats the small slot on the inside...
  14. Replies
    40
    Views
    2,532

    Dek, If I can upload them will do, we have...

    Dek, If I can upload them will do, we have chassis no6 out of 15 approx, all Daimler jag based. Probably the only home built one. Rest were factory I believe
  15. Replies
    40
    Views
    2,532

    So you would pay tax then as only 22 years old? ...

    So you would pay tax then as only 22 years old?

    Some of these earlier correctly name registered cobras that retained the donor reg from the 70’s may well be coming into the historic bracket. ...
  16. Thread: E10!

    by Cobragreyhead
    Replies
    27
    Views
    1,857

    So in short use tesco or esso super 99, do you...

    So in short use tesco or esso super 99, do you still ad an addative on top of that ? Then a drive to mix it uop a bit, then keep tank full ove winter.?
    also worth updating any rubber pipes to...
  17. Replies
    36
    Views
    3,406

    Agreed! Had som 19s on a vectra estate once,...

    Agreed! Had som 19s on a vectra estate once, cracked every month!
  18. Thread: 2030

    by Cobragreyhead
    Replies
    92
    Views
    5,572

    My dad forcast the end of the kit car era some 30...

    My dad forcast the end of the kit car era some 30 years ago ie looking at post sva/iva era ( he was a kit car guy aswell as me) though his view was more the Euro brussels politics would eventually...
  19. Replies
    36
    Views
    3,406

    2 of mine are cracked 17” GTD5 !

    2 of mine are cracked 17” GTD5 !
  20. Replies
    15
    Views
    1,622

    Ditto above. A fight, i left the rachet strap...

    Ditto above. A fight, i left the rachet strap internally placed for two years and like a teeth brace everything lines up now without the rachet
  21. Replies
    20
    Views
    4,092

    Hi I bought some parts of a guy recently who...

    Hi

    I bought some parts of a guy recently who did exactly this
    Dax 351W with 400 bhp and changed carb To an edlebrock system that’s x8 injectors manifold swap, self calibrates, phone app, went...
  22. Replies
    10
    Views
    1,110

    Have x2 non shortened driveshafts for free, just...

    Have x2 non shortened driveshafts for free, just the driveshafts no ujs or ends.
  23. Replies
    26
    Views
    2,361

    Out of interest how do you run your underslung?...

    Out of interest how do you run your underslung? What silencers/bends/ground clearance?
  24. Replies
    7
    Views
    829

    Ditto, foam strips and rivnut idea.

    Ditto, foam strips and rivnut idea.
  25. Replies
    6
    Views
    913

    Also examine the rear anti roll bar mounts (ie...

    Also examine the rear anti roll bar mounts (ie the supports for the twin hoops not suspension) Dax moved them around, if you have the IVA upper seat belt mounts fitted thats cool but then look at the...
Results 1 to 25 of 335
Page 1 of 14 1 2 3 4