Search:

Type: Posts; User: conrod; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    12
    Views
    765

    8V does seem low, but it's difficult to diagnose...

    8V does seem low, but it's difficult to diagnose these things remotely. Fluctuating readings like that from a device that detects voltage/current through a variable resistor suggests variable output...
  2. Replies
    12
    Views
    765

    Paul. Do you have the red wire from the Gauge...

    Paul.

    Do you have the red wire from the Gauge Wizard connected directly to +12v or via the instrument voltage regulator/stabilizer? If it's the latter, then that's probably your issue - but I'm...
  3. Replies
    47
    Views
    4,324

    No problem Chris. Yes, it's a lot easier to...

    No problem Chris.

    Yes, it's a lot easier to fit the driver's side fan with the headers removed!

    If you haven't already done so, while they're off I recommend wrapping the headers with DEI...
  4. Replies
    47
    Views
    4,324

    Here you go. 40067 40068 40069 40070

    Here you go.

    40067

    40068

    40069

    40070
  5. Replies
    47
    Views
    4,324

    LOL! These fans are apparently commonly used...

    LOL!

    These fans are apparently commonly used as case fans in data centres. All I can say is that ear defenders must be standard equipment for the staff! ;)
  6. Replies
    47
    Views
    4,324

    I fitted a pair of these Sanyo Denki 120x120...

    I fitted a pair of these Sanyo Denki 120x120 fans behind the side vents of my Dax. They have an aluminium body and pull 224cfm. They sounded like jet engines when they cut in, but they certainly did...
  7. LOL - Nice one Rocco! :)

    LOL - Nice one Rocco! :)
  8. It'll be just a quick four day blast to...

    It'll be just a quick four day blast to Maastricht and back for Rob and me in his Sumo this time, but we're really looking forward to seeing you guys there.

    Two weeks later we'll be off in my Z4...
  9. The official Dax Corsa B column fitting kit...

    The official Dax Corsa B column fitting kit includes an adapter to which the Sierra column switches and stalks can be mounted - it's the anchor-shaped part in the photo.

    I decided to move to the...
  10. Replies
    17
    Views
    2,283

    Paul, As you've noticed, you'll struggle to...

    Paul,

    As you've noticed, you'll struggle to find 22/22.5 deg hoses - mainly because for such a small angle you should be able to comfortably bend a straight hose to fit. So I'd give that a whirl...
  11. Thread: 3D Printers

    by conrod
    Replies
    22
    Views
    11,398

    Things have moved on for me on the 3D printing...

    Things have moved on for me on the 3D printing front too. My previous plan to build a 400x400 or 500x500 printer got overtaken when I saw an e3D BigBox on Gumtree for £150. The guy had paid over...
  12. Hi Rocco. Did you mean to post photos of the...

    Hi Rocco.

    Did you mean to post photos of the seats as well?

    All th ebest.
  13. Replies
    19
    Views
    1,000

    Who would have thought such a simple device could...

    Who would have thought such a simple device could turn out to be so complicated?!!! :)

    I'm 99.9% certain that this is the same as the alternator fitted to my Dax. It certainly should be because...
  14. Replies
    19
    Views
    1,000

    HI again Chris My ignition lamp used to work...

    HI again Chris

    My ignition lamp used to work fine with an identical alternator, but unfortunately I no longer have either the car or the Dax wiring manual to check the lamp connections!
    ...
  15. Replies
    19
    Views
    1,000

    Hi Chris. From the quick search I've done this...

    Hi Chris.

    From the quick search I've done this does seem to cause quite a bit of confusion, but hopefully this article will be of help.
  16. Replies
    0
    Views
    296

    Bargain Resin 3D Printer on Amazon

    Hi All.

    I've been considering adding a resin printer to my 3D printer collection, and came across this one last night:

    QIDI TECH S-Box 10.1" Resin 3D Printer
    ...
  17. Replies
    16
    Views
    1,904

    Keith, High HC levels are caused by unburnt...

    Keith,

    High HC levels are caused by unburnt fuel in the exhaust. In my experience this is usually due to an ignition fault/misfire, so check the usual things - low tension side wiring, coil, HT...
  18. Replies
    7
    Views
    1,022

    However, I seem to have lost the ability to edit...

    However, I seem to have lost the ability to edit posts! I meant to add that this was the standard Dax supplied rack up until Quinton Hazell ran out of the external case assemblies (and soon after...
  19. Replies
    7
    Views
    1,022

    Hi Steve, This is it: ...

    Hi Steve,

    This is it:


    http://www.cobraclub.com/forum/attachment.php?attachmentid=39770&stc=1

    I've been unable to upload or link to photos on here for years, but magically I'm able to do so...
  20. Replies
    7
    Views
    1,022

    D'oh - I got the rack and the column confused!...

    D'oh - I got the rack and the column confused! :oops:

    Forget eBay - £100 for the rack, including postage!
  21. Replies
    7
    Views
    1,022

    No problem Steve - I'd be happy to send it by...

    No problem Steve - I'd be happy to send it by courier for £160 (£150 plus £10 carriage). If you're happy with that, just make me an offer of £150 on eBay and I'll then accept it.

    I've managed...
  22. Replies
    7
    Views
    1,022

    Dax Parts For Sale

    Hi all.

    Further to my "Garage Clearout" post I thought I'd list the various Dax parts I have, and then take them all to Stoneleigh.

    The list is as follows.

    Sierra steering column (modified) ...
  23. Replies
    5
    Views
    1,031

    Garage Sale Update

    The alternator and the Dax side pipe perforated tubes have now been sold.

    I've added the following this afternoon:

    Speedway / Procomp PCE376 HEI Distributor for Chevy SBC BBC

    Wel-bilt Engine...
  24. Replies
    5
    Views
    1,031

    Thanks David - I've just replied.

    Thanks David - I've just replied.
  25. Replies
    12
    Views
    1,918

    I hooked a spare electric choke up to my bench...

    I hooked a spare electric choke up to my bench power supply. When first connected at 12v the current exceeds that on my power supply ammeter, so is greater than the maxumim reading of 2 amps. As the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4