Search:

Type: Posts; User: 427jlc; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    30
    Views
    1,701

    The aluminium mirror I don't think they are IVA...

    The aluminium mirror I don't think they are IVA complaint as they don't move if you hit something or somebody people put them on after the test .s and j do them I think about £20ish and the bracket...
  2. Replies
    16
    Views
    669

    Sorry Myles, I thought you would be more...

    Sorry Myles, I thought you would be more interested in what temperature you are actually running from the block as a cooler will always reduce the temp but if the temperature is on point in the...
  3. Replies
    30
    Views
    1,701

    SandJ motors type mirrors they make a completely...

    SandJ motors type mirrors they make a completely different arm from brass there is a lot of work in them I have seen them before they start work on them machine work silver soldering and then...
  4. Replies
    8
    Views
    525

    Try SandJ motors quick jack's are made from...

    Try SandJ motors quick jack's are made from stainless steel and mirror polished the wind wings hinges are chrome on brass and they make them not Chinese mayzak zink alloy which can crack the sun...
  5. Replies
    16
    Views
    871

    Also be aware if you don't have the full weight...

    Also be aware if you don't have the full weight of the car with engine, gearbox, electrics, hardware, fluids etc the tyres and wheels won't sit right. What stage of the build are you at??
  6. Replies
    301
    Views
    33,172

    Hi Aaron, you're on the right track, you just got...

    Hi Aaron, you're on the right track, you just got to keep going at it. I used short straight tubes to do this bit as any bends go out of alignment, a 2degree out at the flange can be an inch out 10...
  7. Replies
    30
    Views
    1,701

    Hi Mark, which kit are you building? Lee

    Hi Mark, which kit are you building?
    Lee
  8. Replies
    12
    Views
    757

    Sorry to hear but they did it to my friends car...

    Sorry to hear but they did it to my friends car on IVA, they pull it across an not straight up and so end up as you have! Afterwards we bent the mounting bracket slightly over and I donated my spare...
  9. Replies
    8
    Views
    495

    Try SandJ motors if you have a drawing they will...

    Try SandJ motors if you have a drawing they will have a look at it for you .Tel number 01257 262881 or sandjmotor 427@yahoo.com. ask for John.
  10. Replies
    4
    Views
    327

    NEC Classic car show November.

    Just had a message from John at SandJ motors the NEC Classic car show in November has been CANCELLED .
  11. Replies
    0
    Views
    283

    NEC Classic car show November.

    Just had a message from SandJ motors the November has been CANCELLED tickets will be transferred to next year ? or you can try to ask for your money back ?
  12. Thread: Handbrake

    by 427jlc
    Replies
    8
    Views
    1,154

    Lokar do a tunnel mount handbrake give me a few...

    Lokar do a tunnel mount handbrake give me a few days to get mine back, I have the original cable on the MGB handbrake, cheers
  13. Thread: Handbrake

    by 427jlc
    Replies
    8
    Views
    1,154

    Hi Graham, I have and John at S& J has made it...

    Hi Graham, I have and John at S& J has made it too my design, I'm picking it up this weekend so I can tell you more then. It's on an AK.
  14. Replies
    3,132
    Views
    579,163

    I have been struggling to get my Holley 650...

    I have been struggling to get my Holley 650 double pumper to run well, today I swapped it out for a 770 holley street avenger vacuum secondaries..............what a difference!! The Cleveland goes...
  15. Replies
    20
    Views
    1,340

    That’s the last 3” of wrap

    That’s the last 3” of wrap
  16. Replies
    20
    Views
    1,340

    Paul, I used mikaloor stainless steel hose...

    Paul, I used mikaloor stainless steel hose clamps on the top, fastened underneath so you only see the band on the top, wrapped as far as I could go, finished off with the same Toolstation stainless...
  17. Replies
    28
    Views
    2,680

    Firstly, get your idle down, when stood still...

    Firstly, get your idle down, when stood still it's revving like it does at 30mph in 3rd gear. Secondly the cutting out and difficult to start points to fuel evaporation in the float bowls, a common...
  18. Replies
    41
    Views
    2,854

    Good man James!! Glad you took the plunge it will...

    Good man James!! Glad you took the plunge it will be worth it, I'm chuffed with mine. Give John at S&J motors a ring I'm sure he has an original glove box knob.
    Really admire your work already!
    Lee
  19. Replies
    0
    Views
    324

    NEC November is still on .

    John from S.and J Motors says NEC Birmingham is still on in November upto now have had to make a lot of changes one way system will be in place wider walk ways,masks will have to be worn they will be...
  20. Thread: Column bearings

    by 427jlc
    Replies
    8
    Views
    1,061

    Hi Craig, I stripped mine when I converted it to...

    Hi Craig, I stripped mine when I converted it to top mgb and bottom bmw, if I remember it just knocks out the bottom of the steel tube.
    Lee
  21. Replies
    3
    Views
    578

    Stoneleigh kit car show 2020

    Well Stoneleigh kit car show is off just had message from John at s and J that the 2020 show is off till next year he had a email saying it looks like we are going to have to cancel the show due to...
  22. Replies
    1
    Views
    331

    Give them a call or email...

    Give them a call or email sandjmotors427@yahoo.com they will send you some pictures of what you want to look at ?
  23. Thread: Getrag gearbox

    by 427jlc
    Replies
    7
    Views
    978

    I thought the BMW was a dogleg 1st gear???

    I thought the BMW was a dogleg 1st gear???
  24. Replies
    24
    Views
    1,506

    So which way round should the chamfer point?

    So which way round should the chamfer point?
  25. Replies
    24
    Views
    1,506

    Hi Simon, I think I have the same issue, what Jon...

    Hi Simon, I think I have the same issue, what Jon refers to is the brass spacer that sits at the diff end of the splined end shaft that goes through the hub. If there is no play the hub heats up and...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4