Search:

Type: Posts; User: skinnymathew; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    151

    3D Printed "Shelby Cobra"

    Ok, so it's a bit of a stretch to call it a Shelby Cobra but I stumbled across this looking for 3D printed intake manifolds...


    https://www.youtube.com/watch?v=HXvIMRklWiM
  2. Thread: Engines

    by skinnymathew
    Replies
    13
    Views
    620

    I think it's TonyD?

    I think it's TonyD?
  3. Replies
    19
    Views
    731

    I'm pretty sure I've seen this sellers other...

    I'm pretty sure I've seen this sellers other items before under a different seller ID.
  4. Replies
    8
    Views
    385

    Doh! Having a senior moment and confused happy...

    Doh! Having a senior moment and confused happy Jim commenting on a thread with him starting it...
  5. Replies
    8
    Views
    385

    I thought Happy Jim decided against the Corsa C...

    I thought Happy Jim decided against the Corsa C and put in a Corsa B? http://www.cobraclub.com/forum/showthread.php?t=55509
  6. Replies
    26
    Views
    1,696

    Are you sure it's an O and not a square? Could...

    Are you sure it's an O and not a square? Could mean pounds (lb) per square (O) inch (")...
  7. Replies
    23
    Views
    1,600

    Very nice.

    Very nice.
  8. Replies
    4
    Views
    359

    If it's not a donor standard part/bolt then...

    If it's not a donor standard part/bolt then shouldn't the build manual specify the torque?
  9. Replies
    12
    Views
    1,039

    Maybe try going over the timing marks with a...

    Maybe try going over the timing marks with a white paint pen then skimming off any excess with the sandpaper? Should make them more visible.
  10. Replies
    669
    Views
    67,036

    Not so much Cardboard Aided Design as Hardboard...

    Not so much Cardboard Aided Design as Hardboard Aided Design. I like it.
  11. Replies
    669
    Views
    67,036

    I can see why you didn't want the bodywork until...

    I can see why you didn't want the bodywork until now!
  12. Replies
    4
    Views
    283

    Does anyone here create a list over a few months...

    Does anyone here create a list over a few months and then seek the items out at these events? I doubt I would have the organisation/patience to do this but perhaps it saves money?
  13. Replies
    13
    Views
    1,193

    Unless forgiveness comes with a hefty fine..

    Unless forgiveness comes with a hefty fine..
  14. Replies
    13
    Views
    633

    My gauge reads in Fahrenheit. Maybe Brian's does,...

    My gauge reads in Fahrenheit. Maybe Brian's does, too.
  15. Replies
    26
    Views
    1,349

    I was interested but it's a 9 bolt pattern so...

    I was interested but it's a 9 bolt pattern so it's not for me.
  16. Replies
    26
    Views
    1,349

    Sent email to your btinternet account..

    Sent email to your btinternet account..
  17. An MoT is no replacement for effective regular ...

    An MoT is no replacement for effective regular maintenance but effective regular maintenance is a replacement for an MoT. After all, the MoT only confirms that the car is roadworthy at that...
  18. Replies
    26
    Views
    1,349

    I'm interested in the Pilgrim roll bar and...

    I'm interested in the Pilgrim roll bar and perhaps the mota lita wheel - can you post/send me a photo of the wheel, please?
  19. Replies
    669
    Views
    67,036

    Brilliant progress. It will be test time before...

    Brilliant progress. It will be test time before you know it.
  20. Replies
    15
    Views
    884

    Yes, please. I need more 1UZ goodness to stop me...

    Yes, please. I need more 1UZ goodness to stop me thinking about the 3.0 V6 VVT and manual gearbox that are in the Jaguar S-Type.
  21. Replies
    32
    Views
    3,093

    Have you tried swapping the dampers from side to...

    Have you tried swapping the dampers from side to side or only the springs?
  22. Replies
    23
    Views
    1,380

    At least whilst getting from the garage to the...

    At least whilst getting from the garage to the road.
  23. Replies
    2,967
    Views
    507,856

    Turned my external bonnet hinges into internal...

    Turned my external bonnet hinges into internal bonnet hinges. Now the prototype has been proven, it's time for some bespoke brackets.....
  24. Replies
    2,967
    Views
    507,856

    It's not been my experience that the work stops...

    It's not been my experience that the work stops once the driving starts...
  25. Replies
    4
    Views
    268

    The double thread threw me too. I mentioned the...

    The double thread threw me too. I mentioned the 285/40 because that's a size that Northants stocks and I assumed it would result in a narrower tyre so rubbing would be unlikely, but the calculator...
Results 1 to 25 of 254
Page 1 of 11 1 2 3 4