Search:

Type: Posts; User: alunwill; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Fuel gauge

    by alunwill
    Replies
    5
    Views
    246

    Try the spyda with a vdo gauge (basically a...

    Try the spyda with a vdo gauge (basically a rheostat in a vertical tube).
  2. Thread: Fan fuse

    by alunwill
    Replies
    17
    Views
    842

    Crimp is fine providing you use the right crimper.

    Crimp is fine providing you use the right crimper.
  3. Replies
    21
    Views
    727

    You don't need to heat up or cool down to fit...

    You don't need to heat up or cool down to fit these bearings. Get yourself a suitable size disc, I bought mine,, 6mm thick from fleebay. Not sure the diameter about 50mm I think or get a bearing...
  4. Thread: Fan fuse

    by alunwill
    Replies
    17
    Views
    842

    Make sure you get the cable sizing right with...

    Make sure you get the cable sizing right with regards to run length from the supply. Typically 5% drop maximum along the way.
  5. Replies
    2
    Views
    392

    I had mine factory fitted. Leaked like a tap,...

    I had mine factory fitted. Leaked like a tap, started to split down the centre where it had been over cut when being made, just a waste of money really. Where the rear curves are on the wings the fit...
  6. Thread: Value

    by alunwill
    Replies
    26
    Views
    1,288

    Whereas I agree with the need to control...

    Whereas I agree with the need to control emissions, the so called green revolution of battery powered vehicles appears to be driven by a flawed strategy. That is battery life and the industrialised...
  7. Replies
    7
    Views
    456

    In all fairness, iva inspectors know exactly what...

    In all fairness, iva inspectors know exactly what goes on and can only judge against what's in front of them. My ak passed with no issues using the original wheel which came with the column....
  8. Replies
    7
    Views
    456

    If it's an AK then you'll be using a bmw column I...

    If it's an AK then you'll be using a bmw column I assume. If so, go to the scrappy and you'll pick one up for a fiver. Open choice on what you fancy after iva!
  9. Thread: Rear hub nut

    by alunwill
    Replies
    3
    Views
    441

    Yep, thought about the heat andstayed with...

    Yep, thought about the heat andstayed with castellated nut.
  10. Thread: Rear hub nut

    by alunwill
    Replies
    3
    Views
    441

    Rear hub nut

    Anyone replaced the castellated nut on the rear hub with a nylock type. If so what's the thread size.

    Also, I've got 2 torque settings written down, 95 ftlb and 140 ftlb. Which one is spec
    ...
  11. Replies
    7
    Views
    567

    Bullet wing mirror

    What's the view on bullet wing mirrors and if you've got them fitted, what position in relation to windscreen pillar.

    Currently got modified s+j side pillar mounted mirrors which get in the way if...
  12. Replies
    3
    Views
    507

    No, there's no problem with my car. It's running...

    No, there's no problem with my car. It's running fine. One of my winter jobs is to remove the exhaust gass recovery system and I'm wondering if I remove the crank to air plenum hose and replace it...
  13. Replies
    3
    Views
    507

    Crankcase breather

    Anyone recommend a good breather filter that doesn't allow the inside of the bonnet to mist up!
  14. Thread: Le man's film

    by alunwill
    Replies
    3
    Views
    388

    Le man's film

    Went to see the le man's film regarding the GT40 developed by Shelby and Miles. All-in-all a good film. Assuming the ford politics to be true, I was amazed at the bunch of "crap houses" which ford...
  15. Replies
    21
    Views
    7,223

    Hi Pete, When's the next area cobra get...

    Hi Pete,

    When's the next area cobra get together. Are the sunday meetings still happening.

    Al
  16. Replies
    0
    Views
    254

    Rear hub grease

    Anyone using red rubber grease on their rear hub bearings. Just opened mine to recharge and surprisingly it's red!
  17. Replies
    16
    Views
    1,697

    Anyone fitted one of these Hatton tops to an AK.

    Anyone fitted one of these Hatton tops to an AK.
  18. Replies
    3
    Views
    538

    SPA classic or le mans

    What's the view on Spa classic rather than le man's. Is it worth the trip.
  19. Replies
    10
    Views
    971

    Hylomar blue including the aero version is...

    Hylomar blue including the aero version is useless for fuel sealant applications from my experience. It dissolves in petrol. Just changed my injectors, filter and pump because this stuff dissolved...
  20. Thread: S+j contact

    by alunwill
    Replies
    3
    Views
    339

    S+j contact

    Anyone have an email or telephone details for s+j. Picked a part up at the show only to find it faulty when I got home

    Thanks
  21. Replies
    24
    Views
    3,889

    I ran flow and return under the diff on my build...

    I ran flow and return under the diff on my build with a protective plate underneath. No issues with Iva. I used braided hose with anc fittings for the supply connection. The standard AK connection...
  22. Replies
    7
    Views
    956

    Many thanks, good link

    Many thanks, good link
  23. Replies
    7
    Views
    956

    Lexus fuel injectors

    Anyone changed the injectors on a 1uz engine. If so do you have the part number for a suitable replacement. Just rang Lexus and they quoted £240 + vat for one which is crazy. Clearly they don't want...
  24. Thread: ECM project

    by alunwill
    Replies
    5
    Views
    612

    Thanks for the response lads, I'll do some...

    Thanks for the response lads, I'll do some background work.

    Regards
  25. Thread: ECM project

    by alunwill
    Replies
    5
    Views
    612

    ECM project

    Thinking of swapping out the Lexus ECM for something more updated. Any advice on a suitable alternative.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4