Search:

Type: Posts; User: ramcobra123; Keyword(s):

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    23
    Views
    1,658

    Galaxy radial t/a tyres are supplied by North...

    Galaxy radial t/a tyres are supplied by North Hants tyres and are good economical tyres. I replaced my BFG's with them and had no problem with them.
  2. Replies
    14
    Views
    1,510

    I drive all year round and run 50% antifreeze to...

    I drive all year round and run 50% antifreeze to ensure clean passages in the cooling system. My garage is too damp to allow it to sit still I'm afraid.
  3. Replies
    20
    Views
    1,383

    I got a set from the us and cost 45 dollars, all...

    I got a set from the us and cost 45 dollars, all in. I fitted them to my RAM today and the front end got more stable.
  4. Thread: SR

    by ramcobra123
    Replies
    2
    Views
    644

    I believe they are made by Absolute Horsepower...

    I believe they are made by Absolute Horsepower now.
  5. Replies
    22
    Views
    2,416

    Holleys are renowned for a stumble off idle as...

    Holleys are renowned for a stumble off idle as you accelerate. Alan gave me some tips, as did various forums on setting up the accelerator pump linkage and that cured me stumble. Power valves and cam...
  6. Replies
    4
    Views
    957

    I'll be there, not with the Cobra unfortunately...

    I'll be there, not with the Cobra unfortunately because the regional Green power event is taking place on the circuit. Enjoy the pub after your meet up though, I'll see you all at Cranleigh instead.
  7. Replies
    25
    Views
    1,411

    Gumball for me way back in 1976, Dax's first...

    Gumball for me way back in 1976, Dax's first rolling demonstrator and then Tim Cooke's RAM s/c write up in Kit Car magazine. From then on I knew I'd have a Cobra and it would be a RAM. I'm on my...
  8. Replies
    3,026
    Views
    537,295

    Hi Lee, I would be looking at the accelerator...

    Hi Lee,
    I would be looking at the accelerator pump area, checking the the gap of 15 thou and wide open throttle and that the operating arm was actually touching the cam on the primary circuit. I...
  9. Replies
    3,026
    Views
    537,295

    Standard is 35 thou. If you change the ignition...

    Standard is 35 thou. If you change the ignition system then the gap can increase, it depends on your ignition system. Mine is an MSD 6AL system with an MSD billet distributor and the gap has...
  10. Replies
    5
    Views
    499

    Hi guys, Thank you for the prompt suggestions to...

    Hi guys,
    Thank you for the prompt suggestions to my plight. All the bulbs work and no corrosion in the sockets. The flasher unit is the old cylinder type (42w), suits two 21 watt bulbs per side....
  11. Replies
    5
    Views
    499

    Indicators stopped flashing

    I'm not good with electrics, hence this possibly stupid question. My indicators stopped flashing yesterday, although they remain on when I move the switch from left to right. The dash board warning...
  12. Replies
    20
    Views
    2,419

    It's a GD that has been modified by its owner...

    It's a GD that has been modified by its owner over time to emulate the 427 shape. I met him at Goodwood AC Cobra replicas meeting last year. A very nice guy with an interesting take on Cobra styling.
  13. Replies
    28
    Views
    3,536

    I bought my Galaxies from North Hants to replace...

    I bought my Galaxies from North Hants to replace my BFG's, they were 30+ years old. The ride quality has vastly improved, no shimmy at speed and low road noise. Highly recommended in my opinion,...
  14. Replies
    11
    Views
    1,958

    Yes, I had the suspension set up by Thunder Road...

    Yes, I had the suspension set up by Thunder Road Cars, as well as corner weighted. The tyres have been balanced, although I'm thinking they maybe slightly out of true. The tyres are very old, so I'm...
  15. Replies
    2
    Views
    715

    Thank you, I'll have a look.

    Thank you, I'll have a look.
  16. Replies
    2
    Views
    715

    351c valley pan installation advice

    I've just finished a top end overhaul on my cleveland engine and just need some advice on reinstalling the inlet manifold with a valley pan. What I found on the strip down was RTV both underneath...
  17. Replies
    11
    Views
    1,958

    Thank you James, I'll follow your lead on this...

    Thank you James, I'll follow your lead on this and see if it makes the difference I'm looking for in the handling/steering.
  18. Replies
    11
    Views
    1,958

    Hi James, I spoke to one of the Thunder Road...

    Hi James,
    I spoke to one of the Thunder Road guys and he said either a 1/2" or 3/4" thick spacer, what have you got?
    All the best
    Ian
  19. Replies
    11
    Views
    1,958

    Thank you for that thought, I hadn't considered...

    Thank you for that thought, I hadn't considered that one. I'll check tomorrow and see if that helps.
  20. Replies
    11
    Views
    1,958

    Tyre pressures

    Any RAM owners able to suggest suitable tyre pressures, especially the front ones? I only ask because I get a lot of feedback from the fronts, especially over bumpy ground. I also experience a...
  21. Thank you for the additional advice about...

    Thank you for the additional advice about mountings/timing and plug considerations. More fiddling to enjoy.
  22. Replies
    9
    Views
    855

    I would contact Cheng Lim at Thunder Road Cars...

    I would contact Cheng Lim at Thunder Road Cars and he will advise you properly. The position of your engine may also affect the poundage used for the front springs as well, just a thought. He set...
  23. Update. Issue solved, don't buy cheap rubbish. ...

    Update. Issue solved, don't buy cheap rubbish. I replaced the system with a genuine MSD 6AL box and blaster coil and my problems have all but gone. I just need to re do the timing slightly because...
  24. Certainly food for thought, it all seems to point...

    Certainly food for thought, it all seems to point in the same direction. The control box/wiring is where I need to look further at. The car starts first time and idles well, it just stumbles on...
  25. No it was a pro comp version of a MSD 6 unit, no...

    No it was a pro comp version of a MSD 6 unit, no rev control available.
Results 1 to 25 of 176
Page 1 of 8 1 2 3 4