Search:

Type: Posts; User: incey1966; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    112

    The fuel pump wires come from the dashboard area....

    The fuel pump wires come from the dashboard area.
    Grey and brown.
    As for the engine mounts AK made them up to suit the chevy engine.
    I’d assumed the brackets on the chassis were also...
  2. Cheers Chaps, I’m going to check the...

    Cheers Chaps,

    I’m going to check the pre load on the lifters, I’m hoping I don’t have to adjust them too much which will be a good sign.
    Then change the oil and filter add some run...
  3. I’m pretty sure I’ve got hydraulic lifters. ...

    I’m pretty sure I’ve got hydraulic lifters.
    Therefore I guess I’m checking that there is preload where I would normally be checking the valve lash..
  4. Well it's definitely a flat tappet cam. Just...

    Well it's definitely a flat tappet cam.
    Just been through my engine stuff and found the cam break in procedure.
    I guess I stupidly assumed it had a roller cam because it had roller rockers.

    Now...
  5. Cheers Kev, I seem to remember reading...

    Cheers Kev,

    I seem to remember reading something in my CAM instructions that said it didn’t need to be run in.
    However that could be wishful thinking…
    I’ll be rummaging around in...
  6. 350 Chevy CAM break in (Or Lack of it...)

    Hi All,

    I’m after some advice.
    After reading the post about the chap with engine problems who’s about to put the car through IVA. I think I may also have a problem.
    I was under the...
  7. Replies
    20
    Views
    1,308

    I'm after some if you fancy sharing costs......

    I'm after some if you fancy sharing costs...
    Maybe some others are and we could do a group buy..
  8. Replies
    5
    Views
    553

    Ok Cheers, More knuckle scraping and...

    Ok Cheers,

    More knuckle scraping and expletives then.....
    I think I'll trial it before I fill with brake fluid...
  9. Replies
    5
    Views
    553

    Side Vent and Brake Servo

    I’m in the process of finishing my engine bay, wiring, throttle cable, hooking up brakes etc.
    It has occurred to me that the driver’s side engine bay air vent will be impossible to remove and...
  10. Replies
    10
    Views
    450

    Try David Manners group jag parts. The part...

    Try David Manners group jag parts.
    The part number of the bush is FRC7418J.
    I think that's the part you're after.
  11. Replies
    10
    Views
    450

    I managed to source some off the internet. I'll...

    I managed to source some off the internet.
    I'll see if I can dig out where I got them from..
  12. Replies
    9
    Views
    706

    You'll be needing an adapter kit to mate the...

    You'll be needing an adapter kit to mate the getrag to the chevy bellhousing.
    I've got a Chevy 350 mated to a getrag I my AK.
  13. Replies
    11
    Views
    990

    Lee, your inbox s full. I'll give you a call...

    Lee, your inbox s full.
    I'll give you a call this evening re the steering wheel.

    Cheers

    Mike
  14. Replies
    8
    Views
    745

    Pete, I noticed something very similar on...

    Pete,

    I noticed something very similar on one of AK’s demo Cars.
    When I asked Jon about it he said it was caused by putting the car on a dyno without cooling fans.
    Coincdentally I’m...
  15. Replies
    11
    Views
    990

    Hi Lee, You have a pm.

    Hi Lee,

    You have a pm.
  16. Replies
    7
    Views
    709

    A standard paperclip is a good gauge. If you...

    A standard paperclip is a good gauge.
    If you unfold a paperclip you should be able prod it between your starter teeth and your flywheel teeth.
    If you can't your clearance is too tight. The Real...
  17. Thread: Heater

    by incey1966
    Replies
    3
    Views
    446

    I think AK now offer a fiberglass heater box if...

    I think AK now offer a fiberglass heater box if you don't want to fabricate anything..
  18. Pete, What boots did you use? I was planning...

    Pete,

    What boots did you use?
    I was planning to use something like these which clearly state that they can touch exhaust headers...
    ...
  19. Replies
    5
    Views
    422

    Cheers Chaps, My heater hose has arrived so...

    Cheers Chaps,

    My heater hose has arrived so I'll stick it on before dropping the body on.
    I've removed the SS covering. Was actually pretty easy but it was a nice hot day. I'm sure this helped....
  20. Replies
    5
    Views
    422

    AK Polo Heater hoses

    I am about to do the final fit of my body.
    I was wondering do I need to fit the heater feed pipe to the polo heater before the body goes on?
    It looks like it would be tricky to get at once the...
  21. Replies
    26
    Views
    1,784

    Can you send me a pic please. I'll pm you my...

    Can you send me a pic please.
    I'll pm you my email.

    Cheers

    Mike.
  22. Replies
    7
    Views
    684

    Thanks for the pic Steve. Most helpful..

    Thanks for the pic Steve.
    Most helpful..
  23. Replies
    26
    Views
    1,784

    Are the nudge bars sold? If not i’ll Take them....

    Are the nudge bars sold? If not i’ll Take them.
    Cheers
    Mike.
  24. Replies
    7
    Views
    684

    AK Boot Gas Ram Brkts

    I'm in the process of fitting the AK boot gas rams.
    The brackets supplied are are about 6 inches long.
    i.e the bit that is meant to be bonded to the underside of the boot.
    When you offer the...
  25. Thread: Gas Rams

    by incey1966
    Replies
    4
    Views
    473

    Gas Rams

    I’m about to fit my gas rams.
    The AK method is to use rivets to attach the brackets to the bonnet/boot.
    I was just wondering if people have used other methods to attach them like rivnuts or...
Results 1 to 25 of 282
Page 1 of 12 1 2 3 4