Search:

Type: Posts; User: Vidge; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    1,421

    Hi Geoff I drilled two holes on the lower...

    Hi Geoff

    I drilled two holes on the lower bracket for the lugs on the bottom of the radiator, thes lugs had a thread tapped on then I used rubber washers to provide packing to five enough...
  2. Replies
    8
    Views
    1,421

    I used a radiator from an S14, you need to modify...

    I used a radiator from an S14, you need to modify the Dax mounting brackets slightly but it fits well and provides adequate cooling for a small block chevy. If you go down this route get the three...
  3. Replies
    13
    Views
    2,787

    I'll host it for you lloyd, I have plenty of...

    I'll host it for you lloyd, I have plenty of online storage that can be accessed by all.

    Cheers

    Andy
  4. Replies
    8
    Views
    1,300

    G'Day Chaps It's a Howe 82870...

    G'Day Chaps

    It's a Howe 82870 http://www.howeracing.com/Adobe/BearingDocs.pdf

    Internal diameter of the bearing is 35mm I didn't get a chance to pull the Getrag out as its currently buried under...
  5. Replies
    8
    Views
    1,300

    Hi Pete I'm not sure, I'll measure the...

    Hi Pete

    I'm not sure, I'll measure the internal diameter of the bearing. Fraz has first dibs though.

    Cheers

    Andy
  6. Replies
    8
    Views
    1,300

    Hi Fraz I still have it and I've got a Getrag...

    Hi Fraz

    I still have it and I've got a Getrag box in the garage to try it on. I bought this one because its got a stop built into the bearing that stops the seal popping at full extension (the...
  7. Replies
    8
    Views
    1,041

    Did you put the abs sensor ring back in the hub...

    Did you put the abs sensor ring back in the hub when you reassembled it ?
    16792
  8. Replies
    8
    Views
    1,954

    Lots here Hardware | Hinges and Brackets | Gas...

    Lots here

    Hardware | Hinges and Brackets | Gas Springs

    Avoid car ones, our bonnets and boots are much lighter, these are for equipment doors etc and to be honest probably where the...
  9. Replies
    30
    Views
    5,486

    This happened to a friend of mine, I used an air...

    This happened to a friend of mine, I used an air hacksaw to run up the back of the U channel which was mounted to the inside of the wall. Took a little while and a few blades but we cut through most...
  10. Replies
    18
    Views
    1,782

    Hi Robin Post the dimensions up and I'll have...

    Hi Robin

    Post the dimensions up and I'll have a root about in the junkyard that is my sheds and garage.

    Andy
  11. Replies
    10
    Views
    1,886

    They get around those ! I found mine after I...

    They get around those ! I found mine after I cleared the garage out, cheap and nasty plastic inserts.
  12. Thread: 1 Hour to go

    by Vidge
    Replies
    17
    Views
    1,605

    Happy Birthday matey ! Remember you're only as...

    Happy Birthday matey ! Remember you're only as old as you think you are (about 8 in my case) CAKE AND JELLY ALL ROUND !
  13. Thread: It's back!

    by Vidge
    Replies
    27
    Views
    3,407

    I suggest that all GD owners lock up the cars...

    I suggest that all GD owners lock up the cars nice and tight until it reappears. There are cheaper ways of repairing write offs, if that really is only a CAT D it needs no more than an MOT to get it...
  14. Replies
    13
    Views
    2,012

    Bloody good point that.

    Bloody good point that.
  15. Replies
    6
    Views
    3,541

    http://www.cobraclub.com/forum/attachment.php?atta...

    http://www.cobraclub.com/forum/attachment.php?attachmentid=14517&stc=1&d=1299533790

    I'm helping YAY !
  16. Replies
    13
    Views
    2,012

    When you hook the servo up to the manifold you...

    When you hook the servo up to the manifold you get a fair amount of assistance from the vacuum created.

    Can you get the pedal to the floor when the engine isn't running with a large amount of...
  17. Replies
    4
    Views
    1,234

    If thats the ford modular engine (which it looks...

    If thats the ford modular engine (which it looks like) It won't fit without lots of surgery. The 90's Ace was a chubby b'stard compared to the original.
    ...
  18. Thread: AK Bargain

    by Vidge
    Replies
    49
    Views
    6,283

    View Post

    Me, then I'll stick it back up at 35K :)
  19. Thread: Who's was this?

    by Vidge
    Replies
    4
    Views
    880

    That'll buff out. Is that figure in the top...

    That'll buff out.

    Is that figure in the top left the reserve value ? If so are they crazy ?
  20. Replies
    19
    Views
    2,082

    Probably a ford block, is that why some of them...

    Probably a ford block, is that why some of them are called side oilers ?
  21. Thread: LS1 Engine

    by Vidge
    Replies
    2
    Views
    884

    78KM works out to be about 50K Miles in my head....

    78KM works out to be about 50K Miles in my head. 3 Grand is silly money though for a motor that will need cats. I'll take the whole car for that though :) I'm sure I can fit the drive train in a fiat...
  22. Replies
    11
    Views
    2,969

    Chuck it in a variable speed drill.

    Chuck it in a variable speed drill.
  23. Replies
    11
    Views
    1,990

    Now who do we know that'd ship an engine like...

    Now who do we know that'd ship an engine like that. Oh wait ...... :D
  24. Replies
    9
    Views
    1,157

    From memory you mash the button on the stalk...

    From memory you mash the button on the stalk until the service interval comes up then you hold the trip reset down for a few seconds. At least thats how you do it on a pug, I'm pretty sure you'll...
  25. Replies
    10
    Views
    1,680

    Sorry to hear that Terry, the law of sod has...

    Sorry to hear that Terry, the law of sod has obviously decided you were due a ticket. Get well soon mate , I hope you're all mended by summer drop me a line if you need any running around done down...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4