Search:

Type: Posts; User: rpm015; Keyword(s):

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    17
    Views
    815

    Well using my previous bad experiences as a...

    Well using my previous bad experiences as a warning I would have a damn good poke around and write a quote laying out the extent of my liability in regard to not having done the prep and primering, ...
  2. Replies
    19
    Views
    601

    I would start by checking the timing possibly...

    I would start by checking the timing possibly it's a little too far advanced, then look at plugs to see if they're heavily coked indicating too rich, then you can look at the carb settings, there's...
  3. Replies
    19
    Views
    601

    If its pinking and running on I would say that's...

    If its pinking and running on I would say that's more of a timing issue rather than carb
  4. Replies
    17
    Views
    815

    You'd think that after 40 years he'd be able to...

    You'd think that after 40 years he'd be able to assess a car and give a realistic assessment of what was needed and cost, there will always be pain in the ass customers,..recognising them as they...
  5. The best of those is the silver one but to be...

    The best of those is the silver one but to be honest I don't like any of them, to me they all look a bit tacky, but each to their own , imho no offense intended
    Roger
  6. Replies
    17
    Views
    764

    Tidy, a different modern twist, I like it!

    Tidy, a different modern twist, I like it!
  7. Replies
    17
    Views
    764

    Cheers guys, i like the look of the flat bottomed...

    Cheers guys, i like the look of the flat bottomed dashes but not sure if it would suit my car, luckily the dash is one of those things that is easy to rip out and redo as all the wiring behind is...
  8. Replies
    17
    Views
    764

    https://photos.app.goo.gl/FSQkSsNqEi8bqtL8A ...

    https://photos.app.goo.gl/FSQkSsNqEi8bqtL8A

    That's mine, I made the switch panel from scrap stainless and got a local guy to engrave it
  9. Replies
    22
    Views
    1,069

    http://www.cobraclub.com/forum/showthread.php?t=60...

    http://www.cobraclub.com/forum/showthread.php?t=60938&highlight=Rover+radiator
    Might help
  10. Replies
    5
    Views
    375

    I have a home kit, not the same as he...

    I have a home kit, not the same as he demonstrates, it does work on small items but they have to be perfectly clean and free from oil/grease, it produces a good finish but is not as durable as a...
  11. Replies
    3
    Views
    353

    Mine are the classic VW chrome ones, straight...

    Mine are the classic VW chrome ones, straight swap for the pilgrim ones and look much better, bought them off an Ebay Vw seller
  12. Replies
    3
    Views
    399

    I've just spent an hour watching a Russian in his...

    I've just spent an hour watching a Russian in his shed, ...... fantastic, if I had 1% of his skill with a lathe I'd be happy
  13. Replies
    2
    Views
    370

    That’s what I’m hoping , Ive got a set on the...

    That’s what I’m hoping , Ive got a set on the way thanks to this advert so I’ll see if they’re usable and it may mean getting the block line bored
  14. Replies
    2
    Views
    370

    Rover v8 main cap

    A long shot I know, Due to the lockdown I've dug out the pile of engine parts i got awhile ago to start a re build , it turns out I'm missing number 1 main bearing cap, so does anyone have one to...
  15. Replies
    10
    Views
    749

    If only the roads were as quiet as that...

    If only the roads were as quiet as that nowadays.............hang on they nearly are at the moment
    As an aside, I have a homemade version of that tracking guage they use, I've set up loads...
  16. Thread: lift

    by rpm015
    Replies
    15
    Views
    1,225

    I have...

    I have
    https://photos.app.goo.gl/MopGojmdAJ5WqwRm7
    It doesn't take up too much space and gives me about 1400mm clear height under the car, my garage ceiling is 2800mm high, I could go higher if I...
  17. Replies
    12
    Views
    793

    I've always found Autosol to work on the most...

    I've always found Autosol to work on the most stubborn marks that are a pain in the a** to shift
    For the pain in the ass you need Anusol! :)
    Don't get them mixed up :)
  18. Replies
    40
    Views
    1,175

    Yes that's the one

    Yes that's the one
  19. Replies
    40
    Views
    1,175

    Ah ha!, just had a look on locostbuilders...

    Ah ha!, just had a look on locostbuilders website, it does appear to be a mk2 Granada from the early 80's, so nothing too weird I was getting thrown by the long nose to the prop
  20. Replies
    40
    Views
    1,175

    https://photos.app.goo.gl/SntVkuVZBEvLPW8c6...

    https://photos.app.goo.gl/SntVkuVZBEvLPW8c6
    Hopefully that's some pictures, mine is a mk2 but the diff casing doesn't look like any I can find on t'internet
  21. Replies
    40
    Views
    1,175

    Not too worried about the ratios, more wondering...

    Not too worried about the ratios, more wondering what it's out of
  22. Replies
    40
    Views
    1,175

    Yes the 72gg casing looks a strange one, my car...

    Yes the 72gg casing looks a strange one, my car is much like Bobs', quite quick to 80-90mph and then runs out of puff
  23. Replies
    40
    Views
    1,175

    Thanks Chris, it would be interesting to know...

    Thanks Chris, it would be interesting to know what I've got for possible future problems, that 72GG casting doesn't show up anywhere
  24. Replies
    40
    Views
    1,175

    God knows what I've got!, just had a look under,...

    God knows what I've got!, just had a look under, there's no identity tag on the diff just a case casting number (72GG 4198CA) , can't find that anywhere on the web not even on 7th heaven which has...
  25. Replies
    40
    Views
    1,175

    108mm, don't know about the splines unless I take...

    108mm, don't know about the splines unless I take them out and I don't really want to do that unless I have to, I'll have to see how it goes
Results 1 to 25 of 361
Page 1 of 15 1 2 3 4