Search:

Type: Posts; User: KevinW; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    5
    Views
    192

    same here.

    same here.
  2. Replies
    4
    Views
    383

    Paul - are you going to Goodwood on Sunday?

    Paul - are you going to Goodwood on Sunday?
  3. Replies
    4
    Views
    269

    - been a bit slow sorting this out (work issues)...

    - been a bit slow sorting this out (work issues) - will send over the w/e.
  4. Thread: IVA overriders

    by KevinW
    Replies
    39
    Views
    1,834

    Indeed. I suggest this thread is closed.

    Indeed.
    I suggest this thread is closed.
  5. Thread: IVA overriders

    by KevinW
    Replies
    39
    Views
    1,834

    I think the question then is 'where?' If...

    I think the question then is 'where?'
    If Kiddieminster or Gillingham, then they tend to apply 'scrupulous attention to detail'.
    Other centres have a different approach.

    I didn't have any...
  6. Thread: Seats

    by KevinW
    Replies
    8
    Views
    417

    if you are really tight, MX5 seats might fit.

    if you are really tight, MX5 seats might fit.
  7. Replies
    158
    Views
    13,948

    ....Yup :-P

    ....Yup :-P
  8. Replies
    21
    Views
    1,185

    sure, but as you can see from the above text,...

    sure, but as you can see from the above text, there isn't actually a need to re-set the timing either, if, as my Mum used to say 'leave it as you find it'!
    My concern would be that the engine has...
  9. Replies
    158
    Views
    13,948

    Well done Aaron - similar to what I did.

    Well done Aaron - similar to what I did.
  10. Replies
    21
    Views
    1,185

    you could do this - but the point about the...

    you could do this - but the point about the dizzy method is that it allows pil to move round all the galleries WITHOUT the engine turning. So that when you do turn it with the keey, all th key...
  11. Replies
    6
    Views
    319

    Cover area with making tape, mark preferred...

    Cover area with making tape, mark preferred aperture, or one slightly smaller than planned, and chain drill the area.
    The alternative is to get the Dremel out with a cutting attachment, but you...
  12. Replies
    21
    Views
    1,185

    Good advice from Jon above.

    Good advice from Jon above.
  13. Replies
    4
    Views
    423

    Look forward to the updates. I was involved in...

    Look forward to the updates.
    I was involved in Formula Student some years ago, when most teams abandon motorbike engines for the race cars in favour of electric power, that the Dutch and German...
  14. Replies
    158
    Views
    13,948

    ...raising the gearbox simply allows you to get...

    ...raising the gearbox simply allows you to get an idea of how much movement is needed to gain clearence from the bonnet as skin thickness can be difficult to deduce, thats all.

    Ofcourse an ali...
  15. Replies
    158
    Views
    13,948

    Suggest you unbolt gearbox cross member and jack...

    Suggest you unbolt gearbox cross member and jack up gearbox using trolley jack to tilt the engine. That will help a bit.

    Take a look at your headertank - there is quite a lot that can be chopped...
  16. Replies
    14
    Views
    618

    better than copper? some interesting chat here:...

    better than copper?
    some interesting chat here:
    https://www.researchgate.net/post/For_better_heat_transfer_which_material_should_prefer_first_aluminium_or_copper
  17. Replies
    21
    Views
    825

    OK case proven m'Lords, end of.

    OK case proven m'Lords, end of.
  18. Replies
    21
    Views
    825

    - but there is a nut holding it onto the drive...

    - but there is a nut holding it onto the drive shadft?
  19. Replies
    21
    Views
    825

    just idly wondering about the consequences of...

    just idly wondering about the consequences of just torquing up the nuts and hope for the best..?
  20. Replies
    21
    Views
    825

    ...FFS, what a total pain. Thanks for letting me...

    ...FFS, what a total pain.
    Thanks for letting me know.
    Just seen this, in case you haven't.......
  21. Replies
    3
    Views
    373

    Stoneleigh: date change

    Looks like Stoneleigh is now being held on Sat and Sunday, rather than Sunday and Monday.
    https://www.nationalkitcarshow.co.uk/
  22. Replies
    4
    Views
    269

    Sorry, will clear some space.

    Sorry, will clear some space.
  23. Replies
    14
    Views
    618

    - forgot to add, mine has a big kenlowe sucker on...

    - forgot to add, mine has a big kenlowe sucker on the back.
  24. Replies
    14
    Views
    618

    I think my rad is basically a modified SD1, but...

    I think my rad is basically a modified SD1, but with an extra core.
    Seems to be fine for 7 litres.
  25. Replies
    4
    Views
    269

    FREE: IVA warning lamps

    as per pic, surplus to requirements after Christmas garage clear out.

    Free if you are want them, just let me know.38233
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4