Search:

Type: Posts; User: KevinW; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    12
    Views
    328

    Thanks Jim. Not sure how it would react with the...

    Thanks Jim. Not sure how it would react with the white zircotec coating (which I don't think was a particularly good investment).
  2. Replies
    7
    Views
    145

    That looks like a damn good set up. Guessing the...

    That looks like a damn good set up. Guessing the reserve is around £10-12k but well worth it given what's included.
    If I was retired, I'd jump on that.
  3. The other thing to do is to feed a continuous 12V...

    The other thing to do is to feed a continuous 12V source to the signal wire to check the swing and the stability of the gauge.
    Then ground the feed signal and check that. IIRC the flight range uses...
  4. -aah yes - been there, and forgot to do that!

    -aah yes - been there, and forgot to do that!
  5. Replies
    12
    Views
    328

    well, I've had oil on my headers from a leaky...

    well, I've had oil on my headers from a leaky remote fitting...no fire, but shitty looking headers now :(
  6. also check to make sure your gauges don't need a...

    also check to make sure your gauges don't need a voltage regulator, assuming they aren't mechanical gauges.
  7. Thread: hardtop

    by KevinW
    Replies
    8
    Views
    361

    Dave Brooks ;)

    Dave Brooks ;)
  8. Replies
    7
    Views
    546

    Hi Paul, Had a bit if a setback with the DIY...

    Hi Paul,
    Had a bit if a setback with the DIY here, so won;t be able to make it today. My car off the road as well, sorting out knock-on wheels and some dash modifications.
    Can pop them in the post...
  9. Replies
    6
    Views
    340

    same here.

    same here.
  10. Replies
    7
    Views
    546

    Paul - are you going to Goodwood on Sunday?

    Paul - are you going to Goodwood on Sunday?
  11. Replies
    4
    Views
    306

    - been a bit slow sorting this out (work issues)...

    - been a bit slow sorting this out (work issues) - will send over the w/e.
  12. Thread: IVA overriders

    by KevinW
    Replies
    39
    Views
    1,921

    Indeed. I suggest this thread is closed.

    Indeed.
    I suggest this thread is closed.
  13. Thread: IVA overriders

    by KevinW
    Replies
    39
    Views
    1,921

    I think the question then is 'where?' If...

    I think the question then is 'where?'
    If Kiddieminster or Gillingham, then they tend to apply 'scrupulous attention to detail'.
    Other centres have a different approach.

    I didn't have any...
  14. Thread: Seats

    by KevinW
    Replies
    8
    Views
    453

    if you are really tight, MX5 seats might fit.

    if you are really tight, MX5 seats might fit.
  15. Replies
    159
    Views
    14,249

    ....Yup :-P

    ....Yup :-P
  16. Replies
    23
    Views
    1,467

    sure, but as you can see from the above text,...

    sure, but as you can see from the above text, there isn't actually a need to re-set the timing either, if, as my Mum used to say 'leave it as you find it'!
    My concern would be that the engine has...
  17. Replies
    159
    Views
    14,249

    Well done Aaron - similar to what I did.

    Well done Aaron - similar to what I did.
  18. Replies
    23
    Views
    1,467

    you could do this - but the point about the...

    you could do this - but the point about the dizzy method is that it allows pil to move round all the galleries WITHOUT the engine turning. So that when you do turn it with the keey, all th key...
  19. Replies
    6
    Views
    346

    Cover area with making tape, mark preferred...

    Cover area with making tape, mark preferred aperture, or one slightly smaller than planned, and chain drill the area.
    The alternative is to get the Dremel out with a cutting attachment, but you...
  20. Replies
    23
    Views
    1,467

    Good advice from Jon above.

    Good advice from Jon above.
  21. Replies
    4
    Views
    491

    Look forward to the updates. I was involved in...

    Look forward to the updates.
    I was involved in Formula Student some years ago, when most teams abandon motorbike engines for the race cars in favour of electric power, that the Dutch and German...
  22. Replies
    159
    Views
    14,249

    ...raising the gearbox simply allows you to get...

    ...raising the gearbox simply allows you to get an idea of how much movement is needed to gain clearence from the bonnet as skin thickness can be difficult to deduce, thats all.

    Ofcourse an ali...
  23. Replies
    159
    Views
    14,249

    Suggest you unbolt gearbox cross member and jack...

    Suggest you unbolt gearbox cross member and jack up gearbox using trolley jack to tilt the engine. That will help a bit.

    Take a look at your headertank - there is quite a lot that can be chopped...
  24. Replies
    14
    Views
    690

    better than copper? some interesting chat here:...

    better than copper?
    some interesting chat here:
    https://www.researchgate.net/post/For_better_heat_transfer_which_material_should_prefer_first_aluminium_or_copper
  25. Replies
    21
    Views
    906

    OK case proven m'Lords, end of.

    OK case proven m'Lords, end of.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4