Search:

Type: Posts; User: JamesB; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    290

    RAM engine mounts bolt to the chassis. If the...

    RAM engine mounts bolt to the chassis. If the bolts can take the strain between the mount and the block then they can do the same between the mount and the chassis.
  2. Thread: Rear hub nut

    by JamesB
    Replies
    3
    Views
    332

    I would NOT use a nylock all of that lot gets...

    I would NOT use a nylock all of that lot gets quite hot..... Why would you not use a castellated nut?
  3. Replies
    5
    Views
    513

    Yes please, will PM you

    Yes please, will PM you
  4. Replies
    5
    Views
    513

    Does someone who has quick jacks have a set I...

    Does someone who has quick jacks have a set I could borrow then?
  5. Thread: Bumper grommets

    by JamesB
    Replies
    20
    Views
    1,378

    Actually I think my old ones are serviceable so....

    Actually I think my old ones are serviceable so. I don't think I need a set.
  6. Replies
    5
    Views
    513

    Hi, thanks, I might take you up on your offer but...

    Hi, thanks, I might take you up on your offer but I really need to offer up the bumpers to get the exact bumper iron locations. I am rebuilding a RAM and I have replaced a couple of fibreglass...
  7. Thread: Bumper grommets

    by JamesB
    Replies
    20
    Views
    1,378

    Yes, I need some too!

    Yes, I need some too!
  8. Replies
    5
    Views
    513

    Old front and rear nudge bars

    As title really, I need an old set of nudge bars in order to get the bumper irons in the right place so that I can use quick jacks but at a later date I can fit nudge bars if I want. They can be...
  9. Replies
    6
    Views
    596

    It is indeed easy to take the cap off and get to...

    It is indeed easy to take the cap off and get to the shims, however I would not know where you might get the shims from.
  10. Replies
    4
    Views
    473

    I am a bit late to this but I did actually have...

    I am a bit late to this but I did actually have the distances on a drawing but the problem is that without the actual nudge bars you cant get the height of them right, so even if you intend to fit...
  11. OK, that's interesting, so I can still use the...

    OK, that's interesting, so I can still use the gearbox sensor with one of those dodads. Looks like the way to go.
  12. Well it looks like there none of us have done...

    Well it looks like there none of us have done this, but I was also thinking the same. I am putting in a Tremec TKO 600 and though it would be a lot easier to run it straight of the gearbox. If not I...
  13. Replies
    8
    Views
    682

    Yes, they look like the right fitting for the...

    Yes, they look like the right fitting for the smiths gauges.
  14. Wish I'd seen these before they went on ebay!! ...

    Wish I'd seen these before they went on ebay!!

    Would have saved myself £27!!
  15. Replies
    28
    Views
    4,623

    I have a proper set of drop links to a bracket on...

    I have a proper set of drop links to a bracket on the lower wishbone, which also allows for adjustment. I'll try to take a picture of one end of it.
  16. Thread: Rotary Switches

    by JamesB
    Replies
    6
    Views
    444

    Yes, the key point is the functionality, The...

    Yes, the key point is the functionality, The original switches were not 4 position, only 3 i.e. fan would be off, low, high, wipers would be off, slow, fast. I want three fan speeds and off and I...
  17. Replies
    28
    Views
    4,623

    Interesting about the ARB, Cheng has persuaded me...

    Interesting about the ARB, Cheng has persuaded me that one would benefit my car, so I now have one, but perhaps it will work as it should given that I have different shock absorbers and springs from...
  18. Thread: Rotary Switches

    by JamesB
    Replies
    6
    Views
    444

    Rotary Switches

    I'm looking for some rotary switches with a hex shaft like the original Lucas units for the fan and wipers, but... I'm looking for 4 position switches, i.e OFF-ON-ON-ON. Anyone got a source for...
  19. Replies
    3
    Views
    284

    Thanks Stu, I will be using a Windsor, take it...

    Thanks Stu, I will be using a Windsor, take it that has the same arrangement?
  20. Replies
    3
    Views
    284

    SBF Heater connections

    Is it ok to shut off the heater water flow from the water pump on a SBF or do I need a bypass valve?
  21. Thread: Harness needed

    by JamesB
    Replies
    3
    Views
    740

    I have a pair of second hand but good 3 point but...

    I have a pair of second hand but good 3 point but they are blue, any use?
  22. Replies
    20
    Views
    2,167

    Agreed, IF the nylon band in the nut fails to...

    Agreed, IF the nylon band in the nut fails to stop it coming loose then how would it stop it falling off? The whole point of a Nyloc is to stop it loosening.

    But in answer to your question, I...
  23. Thread: Tyre pressures

    by JamesB
    Replies
    11
    Views
    1,958

    The ones on my car are half an inch.

    The ones on my car are half an inch.
  24. Replies
    3
    Views
    868

    Paul, can you pm me with an email address please....

    Paul, can you pm me with an email address please.

    JB
  25. Thread: Tyre pressures

    by JamesB
    Replies
    11
    Views
    1,958

    Yes, Cheng set mine up as well. I will try to...

    Yes, Cheng set mine up as well. I will try to measure them over the weekend.

    JB
Results 1 to 25 of 255
Page 1 of 11 1 2 3 4