Search:

Type: Posts; User: incey1966; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    21
    Views
    1,250

    Hi, Do you have any sets left? If so, I'll...

    Hi,

    Do you have any sets left?
    If so, I'll take one.

    Cheers

    Mike
  2. Replies
    13
    Views
    943

    Not sure of the exact one as it was a xmas...

    Not sure of the exact one as it was a xmas pressie.
    But it's something like this..

    https://www.manomano.co.uk/p/engine-and-oil-pressure-test-tool-kit-1199773
  3. Replies
    13
    Views
    943

    Pete, I have a pressure testing kit if its any...

    Pete,

    I have a pressure testing kit if its any easier/closer.
  4. Replies
    13
    Views
    696

    If you changed your to you're it would read you...

    If you changed your to you're it would read you are on you are own. So I think you were right first time....
  5. Replies
    2
    Views
    265

    The fuel pump wires come from the dashboard area....

    The fuel pump wires come from the dashboard area.
    Grey and brown.
    As for the engine mounts AK made them up to suit the chevy engine.
    I’d assumed the brackets on the chassis were also...
  6. Replies
    18
    Views
    1,178

    Cheers Chaps, I’m going to check the...

    Cheers Chaps,

    I’m going to check the pre load on the lifters, I’m hoping I don’t have to adjust them too much which will be a good sign.
    Then change the oil and filter add some run...
  7. Replies
    18
    Views
    1,178

    I’m pretty sure I’ve got hydraulic lifters. ...

    I’m pretty sure I’ve got hydraulic lifters.
    Therefore I guess I’m checking that there is preload where I would normally be checking the valve lash..
  8. Replies
    18
    Views
    1,178

    Well it's definitely a flat tappet cam. Just...

    Well it's definitely a flat tappet cam.
    Just been through my engine stuff and found the cam break in procedure.
    I guess I stupidly assumed it had a roller cam because it had roller rockers.

    Now...
  9. Replies
    18
    Views
    1,178

    Cheers Kev, I seem to remember reading...

    Cheers Kev,

    I seem to remember reading something in my CAM instructions that said it didn’t need to be run in.
    However that could be wishful thinking…
    I’ll be rummaging around in...
  10. Replies
    18
    Views
    1,178

    350 Chevy CAM break in (Or Lack of it...)

    Hi All,

    I’m after some advice.
    After reading the post about the chap with engine problems who’s about to put the car through IVA. I think I may also have a problem.
    I was under the...
  11. Replies
    20
    Views
    1,387

    I'm after some if you fancy sharing costs......

    I'm after some if you fancy sharing costs...
    Maybe some others are and we could do a group buy..
  12. Replies
    5
    Views
    605

    Ok Cheers, More knuckle scraping and...

    Ok Cheers,

    More knuckle scraping and expletives then.....
    I think I'll trial it before I fill with brake fluid...
  13. Replies
    5
    Views
    605

    Side Vent and Brake Servo

    I’m in the process of finishing my engine bay, wiring, throttle cable, hooking up brakes etc.
    It has occurred to me that the driver’s side engine bay air vent will be impossible to remove and...
  14. Replies
    10
    Views
    489

    Try David Manners group jag parts. The part...

    Try David Manners group jag parts.
    The part number of the bush is FRC7418J.
    I think that's the part you're after.
  15. Replies
    10
    Views
    489

    I managed to source some off the internet. I'll...

    I managed to source some off the internet.
    I'll see if I can dig out where I got them from..
  16. Replies
    9
    Views
    738

    You'll be needing an adapter kit to mate the...

    You'll be needing an adapter kit to mate the getrag to the chevy bellhousing.
    I've got a Chevy 350 mated to a getrag I my AK.
  17. Replies
    14
    Views
    1,264

    Lee, your inbox s full. I'll give you a call...

    Lee, your inbox s full.
    I'll give you a call this evening re the steering wheel.

    Cheers

    Mike
  18. Replies
    8
    Views
    774

    Pete, I noticed something very similar on...

    Pete,

    I noticed something very similar on one of AK’s demo Cars.
    When I asked Jon about it he said it was caused by putting the car on a dyno without cooling fans.
    Coincdentally I’m...
  19. Replies
    14
    Views
    1,264

    Hi Lee, You have a pm.

    Hi Lee,

    You have a pm.
  20. Replies
    7
    Views
    723

    A standard paperclip is a good gauge. If you...

    A standard paperclip is a good gauge.
    If you unfold a paperclip you should be able prod it between your starter teeth and your flywheel teeth.
    If you can't your clearance is too tight. The Real...
  21. Thread: Heater

    by incey1966
    Replies
    3
    Views
    455

    I think AK now offer a fiberglass heater box if...

    I think AK now offer a fiberglass heater box if you don't want to fabricate anything..
  22. Pete, What boots did you use? I was planning...

    Pete,

    What boots did you use?
    I was planning to use something like these which clearly state that they can touch exhaust headers...
    ...
  23. Replies
    5
    Views
    435

    Cheers Chaps, My heater hose has arrived so...

    Cheers Chaps,

    My heater hose has arrived so I'll stick it on before dropping the body on.
    I've removed the SS covering. Was actually pretty easy but it was a nice hot day. I'm sure this helped....
  24. Replies
    5
    Views
    435

    AK Polo Heater hoses

    I am about to do the final fit of my body.
    I was wondering do I need to fit the heater feed pipe to the polo heater before the body goes on?
    It looks like it would be tricky to get at once the...
  25. Replies
    26
    Views
    1,862

    Can you send me a pic please. I'll pm you my...

    Can you send me a pic please.
    I'll pm you my email.

    Cheers

    Mike.
Results 1 to 25 of 286
Page 1 of 12 1 2 3 4