Search:

Type: Posts; User: alunwill; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    43
    Views
    2,255

    I'm up for that, any dates post June are fine...

    I'm up for that, any dates post June are fine with me. I was aiming to do uk auto museums over the next couple of years so this is a good start.
  2. Replies
    3
    Views
    354

    Predictive text is a pain, it's Tatton Park

    Predictive text is a pain, it's Tatton Park
  3. Replies
    3
    Views
    354

    Tatton park classics

    The dates are out for June, July and August car shows at tattoo Park. Is anyone going, assuming of course covid allowed
  4. Replies
    9
    Views
    905

    Hi Ian, Good data, worth sharing Alun

    Hi Ian,

    Good data, worth sharing

    Alun
  5. Replies
    9
    Views
    905

    Hi tony, How's things going. I used a can...

    Hi tony,

    How's things going.

    I used a can of carb cleaner(aerosol), rigged a tube to feed into the injector and bought a box of tricks of ebay for £20 that allows you to cycle the injector....
  6. Replies
    9
    Views
    905

    Hi Ian, I understand your point but for me the...

    Hi Ian,

    I understand your point but for me the donuts are too rigid and a bit much like "hit or miss" with regards to aligning the seals. The benefit for me of the toyota seal is that it's shaped...
  7. Replies
    9
    Views
    905

    Hi Graham, Yes those are the ones. The...

    Hi Graham,

    Yes those are the ones.

    The toyota part numbers, which rockauto uses are below

    top- 23250B (O ring to fuel rail)
    Middle - 23250C (vibration ring, I think that's what they call...
  8. Replies
    9
    Views
    905

    1uzfe injector seals

    I serviced my injectors a few months ago, replacing all the seals and o rings, together with checking spray patterns but I've had an annoying rough running when I put my foot down. It passed the...
  9. Thread: Megasquirt

    by alunwill
    Replies
    2
    Views
    584

    Thanks Martin, All sorted, I just wasn't...

    Thanks Martin,

    All sorted, I just wasn't looking in the right place


    Many thanks
  10. Thread: Megasquirt

    by alunwill
    Replies
    2
    Views
    584

    Megasquirt

    does anyone have an electronic version of the ms3 manual I could have
  11. Replies
    7
    Views
    531

    Yes I understand the sentiment but second time...

    Yes I understand the sentiment but second time around and 1/4 of the size should reduce it to 2 yrs surely.
  12. Replies
    7
    Views
    531

    That's a nice unit. Where did you get the kit from

    That's a nice unit. Where did you get the kit from
  13. Replies
    7
    Views
    531

    Junior size cobra

    I've been looking for a junior size cobra for my grandson, 5 years old . I'm interested in a kit not the finished article. Any ideas if they are available. Thought I'd try here before I trawl the net
  14. Replies
    3
    Views
    709

    I'd say you were unlucky. Either that or you've...

    I'd say you were unlucky. Either that or you've been switching off whilst on full load which is unlikely to happen. Not sure what size starter motor and alternator you have but that's about the only...
  15. Replies
    14
    Views
    1,279

    One thought, what's the height of your engine...

    One thought, what's the height of your engine mounts. Is the clearance issue linked to hitting the chassis side rail, front to rear.
  16. Replies
    14
    Views
    1,279

    As Tony said, I used a saab pump which had the...

    As Tony said, I used a saab pump which had the same pulley rib as the lexus. Reversed the tensioner and put the alternator on the opposite side of the engine in place of the ac compressor. Had no...
  17. Replies
    16
    Views
    2,178

    It's just the amount of peripheral bits which you...

    It's just the amount of peripheral bits which you need to take off that takes the time òn a Lexus. Driver side a bit o of a pain because of the air input manifold.
  18. Replies
    5
    Views
    794

    It's a while since I put mine together but from...

    It's a while since I put mine together but from memory I think you calibrate the gauge which produces one table and then you calibrate the sender with the fuel, which produces another table. It then...
  19. Replies
    5
    Views
    794

    I installed a vdo and spider. Both work fine...

    I installed a vdo and spider. Both work fine together and far better than the caerbont float style. Just take your time calibrating it. As for compatability with the smiths gauges, I had no issues....
  20. Thread: Ecm choice

    by alunwill
    Replies
    5
    Views
    797

    Ecm choice

    with so many ecms on the market, what are people using and what's the experience regarding installation. Specifically fuel maps etc, installation manuals, UK support and ease of software use
  21. Replies
    3
    Views
    839

    Graham Check out rock auto in the state's. ...

    Graham

    Check out rock auto in the state's. When you take the cost of the components and postage together they normally come in quite reasonable. In fact I had a couple of gaskets delivered for...
  22. Thread: Radiators

    by alunwill
    Replies
    10
    Views
    1,953

    Graham,, What size hole do those grommets from...

    Graham,,
    What size hole do those grommets from trimmer bros need to fit
  23. Thread: Spa gauge

    by alunwill
    Replies
    0
    Views
    310

    Spa gauge

    Has anyone bought one of the spa dual temperature gauges, oil/water. If so do they supply thermistor sensors (normal type) or the super accurate thermocouple as standard when you buy one.

    Thanks
  24. Replies
    17
    Views
    2,213

    I wouldn't bother with them. About the only...

    I wouldn't bother with them. About the only useful fuel sender is a vdo type unit linked to a gauge wizard
  25. Thread: Radiators

    by alunwill
    Replies
    10
    Views
    1,953

    Stephen, Looking at the mustang rads are the...

    Stephen,

    Looking at the mustang rads are the inlet/outlets on the same side or opposites. Also does it have the oil cooler option for an auto box
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4