Search:

Type: Posts; User: johnnyoz; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    502

    Go to Ants Cobra.Slight change in forms,but an...

    Go to Ants Cobra.Slight change in forms,but an asy guide to what to do
    Ants Cobra - Dax 427
  2. Replies
    30
    Views
    5,801

    My Ram has the tank inside the boot,so everything...

    My Ram has the tank inside the boot,so everything can be seen.I took photos of everything that I thought might be a bit hard to see and the tester took those as evidence of compliance.Seat belt...
  3. Replies
    30
    Views
    5,801

    I was asked to show an earth at...

    I was asked to show an earth at Gillingham,gearknob has to conform to radius requiements only
  4. Replies
    18
    Views
    3,490

    Will do.Sounds like a good idea

    Will do.Sounds like a good idea
  5. Replies
    18
    Views
    3,490

    Aaron is spot on.I sent off my registration...

    Aaron is spot on.I sent off my registration documents last week.I got a call from a lovely lady at the DVLA to let me know I should have paid £154 for the tax.She is sending me a stamped,addressed...
  6. Thread: Seat belts

    by johnnyoz
    Replies
    2
    Views
    385

    They are alright.My car just went through...

    They are alright.My car just went through Gillingham with these and passed.Merlin motorsport site says they are alright as well.I printed off the page in case but was not needed
  7. Replies
    7
    Views
    704

    I got an aluminium plate< masked outy two areas...

    I got an aluminium plate< masked outy two areas and sprayed black.Stamped the VIN number and above it the kit make.In my case RAM.Accepted by Gillingham
  8. Replies
    16
    Views
    1,323

    My tester checked the brakes on the rollers and...

    My tester checked the brakes on the rollers and said that they were fine.He drove the car himself and faulted the brake bias.He said "Fit a bias valve,but not too much change as the brake readings...
  9. Replies
    14
    Views
    1,036

    More side access39459 A thin split pin runs in...

    More side access39459 A thin split pin runs in the screw head groove
  10. Replies
    14
    Views
    1,036

    The trick is to adjust the screw rod that runs...

    The trick is to adjust the screw rod that runs across the pivot of the brake caliper,get it close but still with clearance and then adjust the handbrake.I hope that this makes sense
  11. Replies
    16
    Views
    1,323

    The tester just hits the brakes hard and it is...

    The tester just hits the brakes hard and it is his impression.He did mine on a loose bit of gravel and personally I thought it was marginel.Still,don't disagree with the tester......
  12. Replies
    18
    Views
    2,064

    If you have a 3.5 in BSP filler you can get a...

    If you have a 3.5 in BSP filler you can get a loaner cap from Car builder solutions.I have got a cap and I am waiting to see if I own it or they sent me a loaner.Watch this space....
  13. Replies
    16
    Views
    1,323

    Got pinged at Gillingham for brake bias.Bought a...

    Got pinged at Gillingham for brake bias.Bought a Ford Mondeo bias valve from ebay https://www.ebay.co.uk/itm/123727112642 and plumbed into rear brake line.Seems to have done the trick! The make is...
  14. Replies
    20
    Views
    5,315

    A bit of a late reply.There is a number on your...

    A bit of a late reply.There is a number on your confirmation,call it and arrange the test
  15. Replies
    14
    Views
    3,164

    They are 8'' longx2,25id

    They are 8'' longx2,25id
  16. Replies
    10
    Views
    1,509

    I have a RAM .The centre tunnel is so wide,that...

    I have a RAM .The centre tunnel is so wide,that by the time the water gets to the edge it is cold.........
  17. Replies
    14
    Views
    3,164

    I contacted Chen and he suggested 450lbs for...

    I contacted Chen and he suggested 450lbs for single rear shocks.They will arrive today,so will let you know what happens.
    John
  18. Replies
    14
    Views
    928

    Thanks to everyone for all your very helpful...

    Thanks to everyone for all your very helpful advice.I really appreciate it.
    John
  19. Replies
    14
    Views
    928

    Hi Paul,I am going to Gillingham,so am taking no...

    Hi Paul,I am going to Gillingham,so am taking no chances.I have utilized the exempt space for switches,but have 3 gauges plus speedo beyond those.
    John
  20. Replies
    14
    Views
    928

    That would be great.I tried to pm you but your...

    That would be great.I tried to pm you but your inbox is full.If you clear it,I can send you my address.
    John
  21. Replies
    14
    Views
    928

    IVA speedo bezel

    Anybody got any idea where I can get an IVA bezel for a 100mm speedo.Tried Caerbont,don't sell parts,suggested Holdens.Helpful but no idea.Tried Merlin.He said the gauge had a rolled edge and the...
  22. Replies
    25
    Views
    1,389

    I got a steel flywheel for my SBF from...

    I got a steel flywheel for my SBF from Summit.Rotating assembly went for balancing,wouldn't balance and turns out my 28oz flywheel was 24oz.Contacted the maker and they were adamant that I had to...
  23. Replies
    25
    Views
    1,389

    I use this to get close price.Need to know...

    I use this to get close price.Need to know postage to be accurate https://www.simplyduty.com/import-calculator/
  24. Replies
    8
    Views
    794

    I used these.You can thread a nut on first and...

    I used these.You can thread a nut on first and use as a height adjuster https://www.polymax.co.uk/anti-vibration-rubber-mount/rubber-bump-stop/buffer-anti-vibration-mount
  25. Replies
    20
    Views
    5,315

    Posted it two days ago.Got confirmation email...

    Posted it two days ago.Got confirmation email today.So now I just wait
Results 1 to 25 of 99
Page 1 of 4 1 2 3 4