Search:

Type: Posts; User: Markm; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    21
    Views
    1,947

    Can I take a set please if you have any left? I...

    Can I take a set please if you have any left? I send you a PM

    Mark
  2. Replies
    6
    Views
    433

    The plugs and sockets are used for connection, AK...

    The plugs and sockets are used for connection, AK have put those sockets already on the loom, the wires not used can then be removed. No wires need splicing into the loom from memory!

    hope this...
  3. Replies
    30
    Views
    1,597

    Looks absolutely awesome Mark, good luck with...

    Looks absolutely awesome Mark, good luck with your IVA hopefully I'll not be to far behind you!

    Mark
  4. Replies
    3,061
    Views
    546,704

    Looking good Graham! Mark

    Looking good Graham!

    Mark
  5. Thread: Give it away ?!

    by Markm
    Replies
    3
    Views
    378

    Give me an hour I'll pick it up! I'm only up the...

    Give me an hour I'll pick it up! I'm only up the road in Flackwell Heath, Could do with a result having had to spend 9k last week on a sick dog!
    seriously though good luck with your sale!
    Mark
  6. Replies
    0
    Views
    475

    Tremec sensor/Smiths Classic speedo

    Could any one advise me on setting up the Smiths classic speedo if I use the tko 500 speed sensor? Ive read an article referring to using shielded wire which doesn't seem a problem and have the...
  7. Replies
    6
    Views
    993

    I'm pretty sure I only used one Graham! Mark

    I'm pretty sure I only used one Graham!

    Mark
  8. Thread: Battery isolator

    by Markm
    Replies
    3
    Views
    993

    Thanks for the replies Craig! Electrics aren't my...

    Thanks for the replies Craig! Electrics aren't my thing and I was concerned about doing some damage to the Omex, relays on the power side and I had no idea if you'd get a power surge/ spike
  9. Thread: Battery isolator

    by Markm
    Replies
    3
    Views
    993

    Battery isolator

    When using an Omex system does it make any difference to battery isolation ie, the build manual shows the earth going through the isolation switch which is how I was going to do it but thought I ask...
  10. Replies
    3,061
    Views
    546,704

    Nice one Kev, one that's definitely on the wish...

    Nice one Kev, one that's definitely on the wish list! Have you got much to do on it?
  11. Replies
    3,061
    Views
    546,704

    Interior all ordered today! Another milestone!...

    Interior all ordered today! Another milestone! Thanks once again to Wendi and Jon at AK for all the guidance !
  12. Replies
    7
    Views
    876

    Thanks Jon! I'm trying to decide on wheels and...

    Thanks Jon! I'm trying to decide on wheels and tyres at the moment, not to many options if I go for 15's or 16's, mindful I have to get it through the IVA,
    Mark
  13. Replies
    7
    Views
    876

    Do you know if the Cinturato CN12's are OK for...

    Do you know if the Cinturato CN12's are OK for IVA Jon ?

    Mark
  14. Replies
    5
    Views
    733

    Thanks for your replies, I couldn't of been...

    Thanks for your replies, I couldn't of been looking hard enough at the build manual!

    Mark
  15. Replies
    5
    Views
    733

    Indicator stalk ends and IVA

    Do I need to get the car through IVA before changing the indicator stalk ends over to the stainless ones or can I do it before?

    thanks!

    Mark
  16. Replies
    5
    Views
    901

    Graig the spacers between the drive shaft and...

    Graig the spacers between the drive shaft and diff flange don't need to be ground on a surface grinder, they're pretty soft so can be turned down as necessary on a lathe, that's what I did.

    Mark
  17. Thread: Paint choices

    by Markm
    Replies
    7
    Views
    1,278

    I totally ruled out blue, but that only in the...

    I totally ruled out blue, but that only in the end left me with grey or silver on my short list! So I went blue,lots of blues to choose from though! probably going black next time!
  18. Replies
    7
    Views
    857

    Thanks for your replies, I'll get back to work on...

    Thanks for your replies, I'll get back to work on it tomorrow, I think it's bolts and washers for me!
  19. Replies
    42
    Views
    9,998

    Not sure what happened, first pic disappeared,...

    Not sure what happened, first pic disappeared, did it again and got both? Haho!
  20. Replies
    42
    Views
    9,998

    http://www.cobraclub.com/forum/attachment.php?atta...

    http://www.cobraclub.com/forum/attachment.php?attachmentid=35371&stc=1Mines Just back from paint Roger! Yep another blue one, Mark
  21. Replies
    42
    Views
    9,998

    http://www.cobraclub.com/forum/attachment.php?atta...

    http://www.cobraclub.com/forum/attachment.php?attachmentid=35370&stc=1Mines just back from paint a week ago! Yep another blue one! Mark.
  22. Replies
    7
    Views
    857

    Roll bar escusions

    What's the norm? To use stainless self tappers or stainless machine bolts to fix the roll bar escusions , I suppose I'm a little concerned about self tappers lifting the paintwork and gel coat.
    ...
  23. Replies
    42
    Views
    9,998

    Nice choice Anthony! if everything works out ok I...

    Nice choice Anthony! if everything works out ok I should have my AK on the road about the same time,

    Mark
  24. Replies
    3,061
    Views
    546,704

    Bit of milestone today, all ready for paint, just...

    Bit of milestone today, all ready for paint, just got to decide which colour!
  25. Replies
    7
    Views
    966

    Graham I thought your chassis was supplied black...

    Graham I thought your chassis was supplied black powder coated from AK? Same as the wishbones etc you don't need to paint it again unless just for a colour change

    Mark
Results 1 to 25 of 90
Page 1 of 4 1 2 3 4