Search:

Type: Posts; User: incey1966; Keyword(s):

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    77

    Door Hinge Escutcheon Plates

    Has anybody got any pics of the AK door Hinge Escutcheons installed ??
  2. Replies
    5
    Views
    312

    I don't think it matters which way it runs...

    I don't think it matters which way it runs through the heater matrix.
    Are you using the AK stainless heater rail?
    If so I have mine out from the pump through the bottom rail and into the bottom...
  3. Replies
    6
    Views
    296

    I think it's 1/2 NPT to 5/8 you're after. Mine...

    I think it's 1/2 NPT to 5/8 you're after. Mine was from a place called motorsports tools via ebay...
  4. Replies
    6
    Views
    296

    I got mine off ebay I think, Torques maybe.

    I got mine off ebay I think, Torques maybe.
  5. Replies
    10
    Views
    458

    I'm pretty sure I have the same sender in my AK....

    I'm pretty sure I have the same sender in my AK. I'll check the connections and let you know.
  6. Replies
    10
    Views
    458

    If its the float type sender it doesn't matter as...

    If its the float type sender it doesn't matter as it's just acting like a variable resistor..
  7. Replies
    17
    Views
    1,400

    Mark, I may have a 1 piece thick gasket in the...

    Mark, I may have a 1 piece thick gasket in the garage. I will check later.
  8. Replies
    17
    Views
    1,400

    I had a similar issue and the best way to check...

    I had a similar issue and the best way to check which seal you need is to measure your oil pan.
    I think the issue arises because most aftermarket oil pans are designed to use the thicker front seal....
  9. Replies
    4
    Views
    501

    I also have minimal clearance on the offside. I...

    I also have minimal clearance on the offside.
    I had chat with AK about it at Stoneleigh.
    They can sort it for you. Basically I think they fix the engine down and heat the header and then "persuade"...
  10. Replies
    29
    Views
    1,809

    I think I’ve got to the bottom of my sender...

    I think I’ve got to the bottom of my sender problem.
    My Pressure gauge was behaving in a similar fashion to the one’s mentioned in this thread.

    Anyway after Speaking to Caerbont and...
  11. Replies
    29
    Views
    1,809

    Hmmmmm, I got my gauges from digital speedos...

    Hmmmmm, I got my gauges from digital speedos about 18 months ago but just bought the senders from merlin. I think I’ll give Caerbont a call to see what the score is.. seems a bit iffy to be...
  12. Replies
    29
    Views
    1,809

    That's a bit strange. How old are they ? I've...

    That's a bit strange. How old are they ? I've just checked my Caerbont stuff and it says I need a PTTR2300-10-8NKIT.
    This is a 3 wire 0 -5 volt job. They are supposed to be used with all Flight,...
  13. Replies
    3
    Views
    333

    I've just had another look and it appears to be...

    I've just had another look and it appears to be working perfectly now, so that connector could well be the culprit.
    I'll do the same and stick a tie wrap round it.

    Cheers
  14. Replies
    29
    Views
    1,809

    FYI, If you do have the stepper motor type gauge...

    FYI, If you do have the stepper motor type gauge you need a completely different sender. Its a 3 wire job that costs about £95.
    I've just found this out after much wire checking and head...
  15. Replies
    3
    Views
    333

    AK Wash Wipe Operation.

    I’ve got a bit of a strange problem with the windscreen wipers on my AK. At least I think it’s a problem and not a “quirk”.
    The wipers are all working as expected, except for when you pull...
  16. Replies
    6
    Views
    366

    I used one in a similar location. It depends on...

    I used one in a similar location. It depends on your inlet manifold. But I think most have one in that area..
  17. Replies
    0
    Views
    329

    Newtown Bypass Wales (A483)

    Spotted yesterday around 11.30am heading south on the A483
  18. Replies
    21
    Views
    1,859

    Cheers chaps, Pretty much as I thought. I am...

    Cheers chaps,
    Pretty much as I thought. I am also very prone to spilling stuff which was my main reason for considering it.
    I recon it’s more than a £5 difference though. Most places I’ve...
  19. Replies
    21
    Views
    1,859

    Brake Fluid DOT 4 vs DOT 5

    I'm about to fill my brake system.
    I was interested to see if anyone had used silicon based brake fluid (DOT 5).
    If so are there any disadvantages/advantages beside cost that is...
  20. Replies
    17
    Views
    1,783

    Ahh I’m with it now.. I can just draw it out on...

    Ahh I’m with it now.. I can just draw it out on a bit of paper to get the length spot on.
  21. Replies
    17
    Views
    1,783

    AK tank and fuel sender

    I’m just about to fit my fuel sender. It’s the lever and float type affair from caerbont. There’s a table that tells you the arm length required for the measured tank depth. Thing is the table...
  22. Replies
    7
    Views
    753

    Cheers chaps, food for thought. I think I’ll...

    Cheers chaps, food for thought. I think I’ll have a look at shortening the lever first. Then if I’m still not happy it’s out with the dremmel..

    Aaron, headers are from AK. Inch and 3/4 I...
  23. Replies
    7
    Views
    753

    I did think about shortening the gearstick but it...

    I did think about shortening the gearstick but it is already pretty short.
    Altering the bracket and connecting rod would be a lot easier before the body was attached.
    It looks like I might have to...
  24. Replies
    7
    Views
    753

    Getrag Gearbox and AK dash

    I recently finished the cockpit of my AK.
    Then sitting admiring my handy work I put the car in first gear only to smash my hand into the dash......
    Has anyone else had this problem? I'm assuming...
  25. Replies
    8
    Views
    1,344

    Hi Andy, If you're still struggling for clearance...

    Hi Andy, If you're still struggling for clearance K&N do a 2 1/2 inch filter element that will give you a bit more. Looks nice too..
Results 1 to 25 of 314
Page 1 of 13 1 2 3 4