Search:

Type: Posts; User: Russhowell; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    19
    Views
    1,961

    All fittings visible on my web site in the...

    All fittings visible on my web site in the pictures AND documents section for exploded veiws: www.russhowell.com
    also i used Legendarydude.com for his write up

    Cheers
    Russ
  2. Replies
    4
    Views
    98

    Hi Pete, I had been chasing intermittent non...

    Hi Pete,
    I had been chasing intermittent non starting for a few weeks. Turns out the female part in the Crank sensor connector was to big. Squeezed it tighter and now good.
    What ECU have you got,...
  3. Replies
    1
    Views
    358

    Well, i am not sure why i didnt twig this before,...

    Well, i am not sure why i didnt twig this before, but I guess you always think a plug is securely connected once clicked in.

    So I pushed and prodded and unclicked the connections to knock and...
  4. Replies
    1
    Views
    358

    No Green Light only RED - Canems

    Hello,
    I am asking for advice about why my Canems ECU does not show a green light when turning over the engine and proceed to start the car.
    It only has solid red light.

    My understanding is, the...
  5. Replies
    3,355
    Views
    669,090

    I did this recently on my AK. Got a bit ill with...

    I did this recently on my AK. Got a bit ill with the fumes down in the footwells. Take care. Looks awesome though
  6. Replies
    3
    Views
    438

    I cut my panels in half. This was helpful so you...

    I cut my panels in half. This was helpful so you could deal with the back section with the striker and the front section with the door hinges seperately. Instead of having to try and hold the whole...
  7. Replies
    5
    Views
    443

    Hi Mark, A year ago I had exactly the same...

    Hi Mark,

    A year ago I had exactly the same situation. I was very lured by the slick Factory 5 and watched many build videos, but in the end, the final cost totted up to be alot more than buying a...
  8. Replies
    2
    Views
    387

    I think i positioned the mounts in the boot and...

    I think i positioned the mounts in the boot and marked where the vertical uprights were. I then removed mounts and made a 2mm hole staright through the back.
    This then gives you an accurate...
  9. Replies
    10
    Views
    759

    I think i sent my docs in first week of June....

    I think i sent my docs in first week of June. They contacted me approx 12 days later to say I underpaid and needed another cheque for £14.
    Then nothing until I used the direct contact info on the...
  10. Replies
    3
    Views
    386

    Hi, I dont think there is much if any movement in...

    Hi, I dont think there is much if any movement in the door fitting if you remove the door card and unbolt the 4 bolts. The holes are a close fit, so it should re-fit to the same height etc.
    Or, I...
  11. Replies
    11
    Views
    12,479

    Sticky: Thank you for the feedback and the Kudos :) I...

    Thank you for the feedback and the Kudos :)

    I have tested the site in various locations and many devices. I do find that I cannnot look at the site from work if using our secure vpn, but thats the...
  12. Thread: Guages

    by Russhowell
    Replies
    9
    Views
    719

    Hi, I am using Smiths gauges and have the speedo...

    Hi,
    I am using Smiths gauges and have the speedo connection direct from my tk0600 gearbox instead of having to fit a bracket next to diff with magnets.
    All IVA friendly bezels.
    www.russhowell.com...
  13. Replies
    16
    Views
    914

    I would suspect ptfe tape is best bet IF fuel...

    I would suspect ptfe tape is best bet IF fuel resistant, or Blue Hylomar IS a fuel resistant sealant, but not sure how a sealant would perform under pressure.
    Hopefully someone more knowledgeable...
  14. Replies
    6
    Views
    1,534

    Passed Iva on 4/6/21 and Speedo read 4mph under...

    Passed Iva on 4/6/21 and Speedo read 4mph under each of the 5 speed tests.

    Initially I tried programming by driving a set mile which initially seemed quite accurate. The code was: 33258

    However...
  15. Replies
    11
    Views
    12,479

    Sticky: Passed IVA on Friday 4/6/21. No advisories...

    Passed IVA on Friday 4/6/21.
    No advisories except keep heater hose of the starter.
    Handbrake score was 26.

    Well chuffed.
    Will make an IVA section on my site:
    www.russhowell.com

    Cheers
    Russ
  16. Replies
    0
    Views
    413

    Turquoise/blue/green Oxted/edenbridge

    Looked like you were having a good time in the glimpse I got.
  17. Thread: Vin plate

    by Russhowell
    Replies
    1
    Views
    529

    Vin plate

    Hello,
    I have my vin plate but do not know where to fit it.
    It’s an AK cobra, and I need to rivet the plate for IVA.
    I heard it can go in engine bay, on top of passenger footwell? But need to be...
  18. Replies
    4
    Views
    691

    Adam C - Blue Cobra (i think)

    Around 10:30 today (Fri 28th May) on the Kings Road in Fleet, Hampshire.

    I think i just passed Adam C in his blue Cobra, whilst I was returning from a pre-mot in mine......like busses!

    Cheers...
  19. Replies
    9
    Views
    870

    Hi Nigel, I should think you need to 'pull' the...

    Hi Nigel,
    I should think you need to 'pull' the rubber seal forward more than you think. I also 'pushed' it forward with my fingers from cockpit side.
    The rubber grips the body a bit too well, so...
  20. Thread: servo

    by Russhowell
    Replies
    10
    Views
    1,066

    I have a gen 2, but principle is the same. Goto...

    I have a gen 2, but principle is the same.
    Goto www.russhowell.com and view the exhaust section for pictures.
    They come in with approx 10mm clearance above frame, leaving lots of room for brake...
  21. Replies
    21
    Views
    2,563

    lol, i didnt realise the 'back to the future'...

    lol, i didnt realise the 'back to the future' reference, and I am a big fan.

    Brasscraft:
    Prior to setting up Brasscraft, Cris Glover was employed by Panther cars to create the Brightwork for...
  22. Replies
    25
    Views
    3,401

    I think a rounded off square, then fit an...

    I think a rounded off square, then fit an escutcheon, such that AK can provide. Makes it all look pretty,
    Russ
  23. Replies
    21
    Views
    2,563

    I get a faint whaft when I open my boot. I think...

    I get a faint whaft when I open my boot.
    I think the fuel level sender needs tightening slightly or the jubilee clip on the filler pipe.

    Crispian Glover can obviously help source parts but they...
  24. Replies
    13
    Views
    932

    Got a quote from Hart Vehicle Logistics (AK use...

    Got a quote from Hart Vehicle Logistics (AK use them occasionally) Fleet to Peterborough 119 miles approx £250.
    They offered discount if they were already doing a job in same kind of locale. If no...
  25. Replies
    7
    Views
    747

    Few pics of mine, although its an LS3 engine:...

    Few pics of mine, although its an LS3 engine:
    www.russhowell.com
    look at the engine and wiring sections.
    The loom from AK for lights is barely visible in the engine bay as it only goes to starter...
Results 1 to 25 of 49
Page 1 of 2 1 2