Search:

Type: Posts; User: Bannon; Keyword(s):

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: hood

    by Bannon
    Replies
    9
    Views
    223

    Difficult one. My only idea on this would be to...

    Difficult one. My only idea on this would be to install a Naca duct somewhere, which would act like a venturi as the outside air passes over it, drawing cabin air out of the car and reducing the...
  2. For KevinW: The fist pic shows the cross-section...

    For KevinW: The fist pic shows the cross-section of the bottom rail of the frame with the seal attached.
    Third pic: Just enough SikaFlex 221. Don't use too much.
    Second pic: Pespex cut and...
  3. Replies
    3
    Views
    124

    I don't like too many escutcheons - it becomes...

    I don't like too many escutcheons - it becomes blingy and tacky. A clean edge is often a classier finish.
  4. So - first pic in the above post shows the front...

    So - first pic in the above post shows the front roofline. The moulding was trimmed too high above the driver's position, so I had a choice - either trim it higher all the way across, or add fresh...
  5. Yeah, thanks. An unforeseen challenge at every...

    Yeah, thanks. An unforeseen challenge at every stage though - I'll expand on that shortly. I seem to be able to upload photos if I save them to my computer first, instead of going straight from my...
  6. https://i.ibb.co/zFGgSqt/thumbnail-IMG-2278.jpg ...

    https://i.ibb.co/zFGgSqt/thumbnail-IMG-2278.jpg


    https://i.ibb.co/2nQqL3k/thumbnail-IMG-2277.jpg


    https://i.ibb.co/qYmHF6X/thumbnail-IMG-2276.jpg

    ...
  7. Replies
    4
    Views
    254

    Hi, I've done this conversion. Missing from your...

    Hi, I've done this conversion. Missing from your photos are: Corsa B column and ECU. Modified Corsa B lower column section (from JK). 50A fuse holder. Heavy gauge cable for main power feed. I...
  8. Bollocks to this. I'm doing some really good...

    Bollocks to this. I'm doing some really good work, massively useful to others - and all I get is stress. Nothing fecking works - can't upload anything. I'll finish my project which is going really...
  9. Err..

    That's not what it looks like! I welded plates to the loose nuts behind the striker plates and glassed them in because it was better than loose nuts which kept moving around. My original post would...
  10. https://i.ibb.co/Q65VTKm/IMG-2229.jpg ...

    https://i.ibb.co/Q65VTKm/IMG-2229.jpg

    https://i.ibb.co/vcB87GT/IMG-2228.jpg

    https://i.ibb.co/X3ggVxG/IMG-2227.jpg

    https://i.ibb.co/8dxbYCp/IMG-2226.jpg
  11. No. Anything longer than a single sentence...

    No. Anything longer than a single sentence causes the error message. I'm about to give up on this thread. There's a problem somewhere.
  12. ATTTENTION MODERATORS: I cannot submit any...

    ATTTENTION MODERATORS: I cannot submit any meaningful posts on this thread any longer. I just get 'INTERNAL SERVER ERROR'. I've been trying for a week, from different locations. Any ideas?
  13. Test...

    I'm trying to submit a new post but the site crashes my computer and I have to re-boot everything each time. This one is a test.
  14. Tailgate done! Well, minus the glass, but I have...

    Tailgate done! Well, minus the glass, but I have just taken delivery of a fiercely powerful pair of suction handles for when I eventually tackle the job.
    It's mostly been fairly smooth sailing...
  15. Replies
    7
    Views
    328

    Pun intended?...heh...

    Pun intended?...heh...
  16. Replies
    16
    Views
    1,457

    I've sent you a PM.

    I've sent you a PM.
  17. Replies
    16
    Views
    1,457

    I'd also like those dimensions Chris, might help...

    I'd also like those dimensions Chris, might help me when the time comes!
  18. The bolts just go through holes in the grp. ...

    The bolts just go through holes in the grp. However, I feel it's slightly crude although I haven't yet given much thought to refining it. I suppose ferrules or escutcheons of some kind could be...
  19. Typos

    I've gone a bit further with the fit since last post, with the roof bolted down I turned my attention to the tailgate. The tailgate isn't an impressive moulding. It's ok - and once complete it...
  20. Replies
    211
    Views
    21,096

    Fantastic work! Totally the right thing to do, ...

    Fantastic work! Totally the right thing to do, I bet you can feel that already. Nothing worse than wishing you'd done something a different way when it's too late to change it. Great job.
    ...
  21. Replies
    211
    Views
    21,096

    Yeah!!! Chop Suey!!! Interested to know how you...

    Yeah!!! Chop Suey!!! Interested to know how you have secured the position of the wishbone mount - I guess you've jigged it into position prior to removing the beam?
  22. Replies
    211
    Views
    21,096

    Blimey - how the plots always thicken, eh? I...

    Blimey - how the plots always thicken, eh? I think the extra work for the 40mm drop sounds well worth the time and effort. Anything else would be a compromise. Sounds amazing though, and so worth...
  23. I've completed the initial fit now, pretty happy...

    I've completed the initial fit now, pretty happy with the overall result, although I do have a few stress-cracks to grind out and fill which have appeared at one of the rear-deck fittings. I don't...
  24. Seconded. If your ignition is electronic, you've...

    Seconded. If your ignition is electronic, you've most likely fried it. I did the same thing years ago with a Pertronix electronic ignition conversion which replaces the points in the distributor. ...
  25. I used up most of my abrasives doing this - but...

    I used up most of my abrasives doing this - but the hinges have come up ok really, I wasn't going for a highly polished finish, and they're stainless so it's hard going - but compared to the...
Results 1 to 25 of 386
Page 1 of 16 1 2 3 4