Search:

Type: Posts; User: jon1d; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3,350
    Views
    667,398

    I wonder if you can use the same mix for mohair...

    I wonder if you can use the same mix for mohair tonneau covers and roofing.
  2. Replies
    5
    Views
    239

    The last over haul of the hand brake. 1....

    The last over haul of the hand brake.

    1. Replaced 17 locking tab
    2. Replaced 18 the brass two pronged space adjuster. These can crack around the hole.
    3. Red grease 5 wheel and 4 . Inspect no4...
  3. Replies
    5
    Views
    239

    If you have good access through your inspection...

    If you have good access through your inspection hatch . You just need the right socket to get on the blind nut. It is well buried. Easy to change . Adjustment is key so check the brass spacer prong...
  4. Replies
    3,350
    Views
    667,398

    Chris, I would be interested which garage you...

    Chris,

    I would be interested which garage you used as I get asked by a number of people for an old school garage.

    John
  5. Replies
    554
    Views
    75,586

    That's handy having a milling machine to do...

    That's handy having a milling machine to do brackets and small parts. Not all of us have a lathe and milling machine lol. Small steps and progress. I bet this weather makes all the difference. Maybe...
  6. Replies
    8
    Views
    371

    Another for the Bosch S5. Round post. Cranks my...

    Another for the Bosch S5. Round post. Cranks my Ford 351c no problem and great storage over winter period.

    008 BOSCH CAR BATTERY 12V 77AH TYPE 096 S5008

    These are also good

    Varta Silver 096...
  7. Replies
    16
    Views
    759

    I think it does depend on your diff and the LSD...

    I think it does depend on your diff and the LSD clutch plates and friction surfaces. The build manual I had changed the quality but you should obtain a manual. I had one for the Dana 44 Spicer diff ....
  8. Replies
    16
    Views
    759

    Tinkas figures sound right . I tested mine at...

    Tinkas figures sound right . I tested mine at 25lbs .
    You remove the amount of clutch plates from 5 to 3. If you do not derate the rear will only under high loads transfer and not progressive at a...
  9. Replies
    16
    Views
    952

    I think those threads are not cut but pressed and...

    I think those threads are not cut but pressed and have a high tensile strength rating.
    Jag used these threads in high stress areas like propshafts and drive bolts. It's the sheer rating.
  10. Replies
    16
    Views
    759

    The diffs are very similar in construction. The...

    The diffs are very similar in construction.
    The problem will be finding might be the bearings if you have a rare early diff but you will just need to find the markings on the bearings.
    A spreader...
  11. Replies
    16
    Views
    759

    They should not be locked. The plates should slip...

    They should not be locked. The plates should slip after about 25 lbs I recall.
    If they do not that's like a locked diff or something has seriously gone wrong internally.
    Wards Engineering or...
  12. Thread: Newbie saying Hi

    by jon1d
    Replies
    9
    Views
    734

    It might be the Chevy 502cu engine injection...

    It might be the Chevy 502cu engine injection which is what Dax put in there last demonstrator.
    Looks a nice car and you will have great fun. I would not worry about mpg unless you were looking at...
  13. Replies
    5
    Views
    437

    Does look like a different colour to Guardsman...

    Does look like a different colour to Guardsman Blue to me. Are there different versions of Guardsman Blue.
  14. Replies
    23
    Views
    1,954

    That's brilliant. Very interesting to see the...

    That's brilliant. Very interesting to see the actual figures. That's a good improvement. Your design takes it to another level of 70% improvement torsion rigidity. Looking at your figures earlier...
  15. Replies
    5
    Views
    437

    Interesting to see these go through the auctions...

    Interesting to see these go through the auctions as they attract so much attention.
  16. Replies
    5
    Views
    547

    James, I think my mail box was full. You...

    James,

    I think my mail box was full. You should be ok to send me a message.

    John
  17. Replies
    23
    Views
    1,954

    That's some gains in rigidity. The Dax back bone...

    That's some gains in rigidity. The Dax back bone was a lot less and would be interested in how much that improved the chassis.
    Concerning the gearbox location for the gear shift is in front of the...
  18. Replies
    23
    Views
    1,954

    Your tunnel section has been modified...

    Your tunnel section has been modified considerably.. I can see this will add extra rigidity. It will restrict space and you have gear box gear level position access ?
  19. Replies
    3,350
    Views
    667,398

    The old stethoscope technique always works. Use...

    The old stethoscope technique always works. Use the longest screw driver against your ear. Watch out for moving parts and work your way along the top covers and exhaust manifold. Great method for...
  20. Replies
    5
    Views
    547

    James, PM Good luck with the sale of the car....

    James,

    PM
    Good luck with the sale of the car. I have sent you a P.M. which you might consider.

    John
  21. Thread: Coil questions

    by jon1d
    Replies
    14
    Views
    910

    The standard mounting position is on the front on...

    The standard mounting position is on the front on the block which seems to be far enough away and vertically mounted. Electrics and heat do not go together well so a coolest location the better. Came...
  22. Replies
    11
    Views
    2,130

    We had some rain on route M25 in the morning but...

    We had some rain on route M25 in the morning but dry and sunny in the afternoon. The brave turned up hoods or no hoods. It was superisily well attended with the weather forecast and social...
  23. Replies
    5
    Views
    438

    If it's your first build you will need lots of...

    If it's your first build you will need lots of support. It's very handy if they close so you can pop down to the factory to pick up parts or look at there demo vehicle.
    What put me off the FF5 was...
  24. Replies
    3
    Views
    398

    Thanks Ambar, I have P.M. you my mobile...

    Thanks Ambar,

    I have P.M. you my mobile number. Was wondering if you just might be at Brands Hatch this weekend, if not I will look to pop down for pick up.

    Cheers
  25. Replies
    3
    Views
    398

    I will take the centre tunnel section if its for...

    I will take the centre tunnel section if its for back bone brace.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4